"A " CNS Standards List |
|
CNS 12854
2017 Edition Fire Fighting Equipment for Liquefied Petroleum GAs Plant Use 液化石油氣設施用消防設備 |
![]() |
|
|
CNS 3497
2017 Edition CAnned tomatoes 番茄罐頭 |
![]() |
|
|
CNS 15562-7
2017 Edition StAtionary training equipment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備-第7部:划船機-附加之特定安全要求與試驗法 |
![]() |
|
|
CNS 283
2017 Edition Methods of sAmpling and chemical analysis of common salt 工業鹽取樣法及化學分析法 |
![]() |
|
|
CNS 5961
2017 Edition GenerAl Rules for Inspection of Valves 閥之檢驗總則 |
![]() |
|
|
CNS 1358
2017 Edition Method of Test for Folding EndurAnce of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
![]() Translated |
|
|
CNS 11156
2017 Edition GreAse Guns-Dimensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒(空)主要尺寸 |
![]() |
|
|
CNS 5770
2017 Edition GenerAl Specification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
![]() |
|
|
CNS 11329
2017 Edition Test Method for the Sets of High Strength HexAgon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
![]() |
|
|
CNS 13464
2017 Edition Method of Liquid PenetrAnt Test for the Welds of Steel Structure 鋼結構銲道液滲檢測法 |
![]() |
|
|
CNS 6860
2017 Edition RespirAtory protective devices − Self-contained open-circuit compressed air breathing apparatus with full face mask − Requirements, testing, marking 呼吸防護裝置-全面罩壓縮空氣開放式自攜呼吸器-要求、試驗、標示 |
![]() |
|
|
CNS 1014
2017 Edition Picks (Single), One TAper End Only 十字鎬(各部份名稱) |
![]() |
|
|
CNS 12887-1
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法─80℃及65%R.H.濕熱處理 |
![]() Translated |
|
|
CNS 12865-1
2017 Edition Method of Test for DigitAl Microelectronics ( High Level Output Voltage ) 數位微電子檢驗法(高位準輸出電壓) |
![]() |
|
|
CNS 11400
2017 Edition Method of Eddy Current Test for MetAl Bars Rods and Wires 金屬棒桿及線渦電流檢驗法 |
![]() |
|
|
CNS 503
2017 Edition ISO Metric Fine Screw ThreAds (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6(ISO制)(標稱直徑18至150公釐,螺距2公釐) |
![]() |
|
|
CNS 9369
2017 Edition Method of Test for Low Frequency (Below 3 MHz) ElectricAl Connectors (TP - 35 Proposed Insert Retention) 頻率3MHz以下電連接器檢驗法(接觸端子插入扣鎖TP–35) |
![]() |
|
|
CNS 14466-18
2017 Edition Audiovisual, video and television equipment and systems - Part18: Connectors for automatic slide projectors withe built-in triacs for audiovisual application 視聽.影像及電視設備與系統-第18部:視聽應用具內建三端閘流體之自動幻燈片投影機之連接器 |
![]() |
|
|
CNS 8918
2017 Edition PrimAry Standards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
![]() |
|
|
CNS 15581
2017 Edition GrAding rules for hardwood sawn lumber 闊葉樹製材分等 |
![]() |
|
|
CNS 12937
2017 Edition Structure of Welded SteelTAnks for Petroleum Oil Storage 鋼製全熔接石油類儲槽構造 |
![]() |
|
|
CNS 6834-8
2017 Edition Testing methods for rubber And plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法-第8部:無撓曲液壓脈衝試驗 |
![]() |
|
|
CNS 1217
2017 Edition Method of prActice for manual sampling of petroleum and petroleum products 石油及其產品手動取樣法 |
![]() |
|
|
CNS 698
2017 Edition Method of Test for Activated Carbon (Power, for Industrial Use) 工業用活性碳(粉狀)檢驗法 |
![]() |
|
|
CNS 14257
2017 Edition Method of test for leAkage rate respirator facepiece 呼吸防護具面體洩漏率試驗法 |
![]() |
|
|
CNS 2671
2017 Edition GAlvanized Low Carbon Steel Wire Strand 鍍鋅低碳鋼絞線 |
![]() |
|
|
CNS 4252
2017 Edition Spring WAshers Curved or Crinkle Type 反向曲線形或波浪形彈簧墊圈(高壓縮負荷彈簧墊圈) |
![]() |
|
|
CNS 12784
2017 Edition Method of Test for In-PlAne Shear Propetries of Glass Fiber Reinforced Plastics 玻璃纖維強化塑膠之面內剪斷性能測定法 |
![]() |
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭(打銷用) |
![]() |
|
|
CNS 66
2017 Edition SquAre Heads and Holes (for Shaft, Hand Wheel and Handles) 方頭及方孔(用於軸,手輪及手柄) |
![]() |
Find out:15242Items | To Page of: First -Previous-Next -Last | [300] [301] [302] [303] [304] [305] [306] |