"I " CNS Standards List |
|
CNS 6834-8
2017 Edition TestIng methods for rubber and plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 12887-1
2017 Edition Method of Test for Accelerated AgIng of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法─80℃及65％R.H.濕熱處理 |
Translated |
|
|
CNS 1014
2017 Edition PIcks (Single), One Taper End Only 十字鎬（各部份名稱） |
|
|
|
CNS 15969
2017 Edition Structural requIrements of railway vehicle bodies of the locomotives and passenger rolling stock 機車及客車軌道車輛車體結構要求 |
|
|
|
CNS 513
2017 Edition MetrIc Trapezoidal Screw Threads Allowance and Tolerances for General Purpose Trapezoidal Screw Threads 梯形螺紋（一般用梯形螺紋的裕度及公差） |
|
|
|
CNS 2671
2017 Edition GalvanIzed Low Carbon Steel Wire Strand 鍍鋅低碳鋼絞線 |
|
|
|
CNS 8918
2017 Edition PrImary Standards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
|
|
|
CNS 12854
2017 Edition FIre Fighting Equipment for Liquefied Petroleum Gas Plant Use 液化石油氣設施用消防設備 |
|
|
|
CNS 5961
2017 Edition General Rules for Inspection of Valves 閥之檢驗總則 |
|
|
|
CNS 12865-1
2017 Edition Method of Test for DIgital Microelectronics ( High Level Output Voltage ) 數位微電子檢驗法（高位準輸出電壓） |
|
|
|
CNS 5770
2017 Edition General SpecIfication for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 503
2017 Edition ISO Metric Fine Screw Threads (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6（ISO制）（標稱直徑18至150公釐，螺距2公釐） |
|
|
|
CNS 16022
2017 Edition AcoustIcs − Determination of dynamic stiffness − Part 1: Materials used under floating floors in dwellings 聲學－動態剛性測定法－用於住宅浮式地板下之材料 |
|
|
|
CNS 11400
2017 Edition Method of Eddy Current Test for Metal Bars Rods and WIres 金屬棒桿及線渦電流檢驗法 |
|
|
|
CNS 3094
2017 Edition SolId Punches 衝頭 |
|
|
|
CNS 11329
2017 Edition Test Method for the Sets of HIgh Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
|
|
|
CNS 283
2017 Edition Methods of samplIng and chemical analysis of common salt 工業鹽取樣法及化學分析法 |
|
|
|
CNS 1358
2017 Edition Method of Test for FoldIng Endurance of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
Translated |
|
|
CNS 13194
2017 Edition Test Methods for Performance and Accuracy of Double SIzers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 15207-10
2017 Edition Road vehIcles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 10: Immunity to conducted disturbances in the extended audio frequency range 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第10部：音頻延伸範圍之傳導擾動免疫力 |
|
|
|
CNS 15504
2017 Edition HIgher yield strength steel plates for bridges 橋梁用高降伏強度鋼板 |
|
|
|
CNS 14466-18
2017 Edition AudIovisual, video and television equipment and systems - Part18: Connectors for automatic slide projectors withe built-in triacs for audiovisual application 視聽．影像及電視設備與系統-第１８部：視聽應用具內建三端閘流體之自動幻燈片投影機之連接器 |
|
|
|
CNS 15581
2017 Edition GradIng rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 4491
2017 Edition LIfting Eye Bolts 吊環螺釘 |
|
|
|
CNS 1217
2017 Edition Method of practIce for manual sampling of petroleum and petroleum products 石油及其產品手動取樣法 |
|
|
|
CNS 12937
2017 Edition Structure of Welded SteelTanks for Petroleum OIl Storage 鋼製全熔接石油類儲槽構造 |
|
|
|
CNS 4579
2017 Edition Bolted ConnectIons with Reduced Body; Bolts 減徑柄螺栓之結合法（螺栓） |
|
|
|
CNS 11156
2017 Edition Grease Guns-DImensions of Grease Cartridges for Lever Hand Guns 手用桿壓式黃油槍用存油筒（空）主要尺寸 |
|
|
|
CNS 4252
2017 Edition SprIng Washers Curved or Crinkle Type 反向曲線形或波浪形彈簧墊圈（高壓縮負荷彈簧墊圈） |
|
|
|
CNS 8473
2017 Edition PIn Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
| Find out:15020Items | To Page of: First -Previous-Next -Last | [296] [297] [298] [299] [300] [301] [302] |
