"M " CNS Standards List |
|
CNS 552
2017 Edition Pencil, coloured pencils and leads for theM 鉛筆、顏色鉛筆及其筆芯 |
|
|
|
CNS 8081
2017 Edition Methods of Performance Test of Panels for Building Construction 建築用組件（嵌板）性能檢驗法 |
|
|
|
CNS 13514
2017 Edition Ready - Mixed Mortar for Unit Masonry 磚、石墁砌用預拌墁料 |
|
|
|
CNS 14778
2017 Edition TerMinology relating to protective clothing 防護衣詞彙 |
|
|
|
CNS 10875
2017 Edition Method of Test for Fiber Optic Devices ( FOTP-4 Temperature Life Test ) 光纖裝置檢驗法（溫度壽命試驗ＦＯＴＰ–４） |
|
|
|
CNS 4662
2017 Edition Open Insert Nuts for Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 13595
2017 Edition Methods of Test for Several Characteristics of Textile Floor Coverings 纖維製地毯類織物之性能試驗法 |
|
|
|
CNS 13143
2017 Edition Method of Test for Internal Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法（使用Ｚ–方向拉／壓式試驗機） |
Translated |
|
|
CNS 4448
2017 Edition Method of Test for Stiffness in Torsion of Plastics as a Function of Temperature 塑膠扭轉剛性與溫度關係測定法 |
|
|
|
CNS 12667
2017 Edition Method of Test for Qualification of Welding Procedure 熔接施工法之確認試驗法 |
|
|
|
CNS 4762
2017 Edition Method of 5 Percent Sulfuric Acid Test for Stainless Steels 不銹鋼之５％硫酸腐蝕試驗法 |
|
|
|
CNS 15628-1
2017 Edition Wheelchair seating - Part 1: Vocabulary, reference axis convention and Measures for body segments, posture and postural support surfaces 輪椅乘坐系統－第1部：詞彙、參考軸協定及身體肢段、姿勢與姿勢支撐面之量測 |
|
|
|
CNS 15539
2017 Edition GyMnastic equipment - Wall bars and lattice ladders 體操設備－壁面肋木架及格子梯 |
|
|
|
CNS 512
2017 Edition Metric Trapezoidal Screw Thread (Genral Plan) 梯形螺紋（總則） |
|
|
|
CNS 12253
2017 Edition Quartz Crystal Units For Oscillators (For 1 MHz -- 125 MHz) 振盪器用石英振盪晶體（１ＭＨｚ～１２５ＭＨｚ用） |
|
|
|
CNS 12895
2017 Edition Rubber Hose Connections for Welding and Cutting EquipMent 熔接與截割器（切斷器）用橡皮軟管接頭 |
|
|
|
CNS 4121
2017 Edition Type N1 standard test block for ultrasonic norMal beam testing of steel plates 超音波檢測鋼板用Ｎ１型標準規塊 |
|
|
|
CNS 504
2017 Edition ISO Metric Fine Screw Threads (Diameters from 30 to 250 mm and Pitch 3 mm) 公制細螺紋7（ISO制）（標稱直徑30至250公釐，螺距3公釐） |
|
|
|
CNS 13245
2017 Edition Method of Test for Rubber Condoms 乳膠製衛生套檢驗法 |
Translated |
|
|
CNS 60227-1
2017 Edition Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V − Part 1: General requireMents 額定電壓450/750 V以下聚氯乙烯絕緣電纜－第1 部：一般要求 |
|
|
|
CNS 366-9
2017 Edition Safety requireMents for cycles − Part 9: Saddles and seat-post test methods 自行車安全要求－第9部：座墊及座桿測試法 |
|
|
|
CNS 6881
2017 Edition Machine Taps for Coarse ISO Metric Threads 螺紋攻（ＩＳＯ公制粗螺紋、機用） |
|
|
|
CNS 9367
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 14 Ozone Exposure) 頻率３ＭＨｚ以下電連接器檢驗法（耐臭氧試驗ＴＰ–１４） |
|
|
|
CNS 7002
2017 Edition Machine Taper Pin Reamers with Parallel Shanks 推拔銷鉸刀（圓柱柄，機用） |
|
|
|
CNS 12293
2017 Edition Reliability Assured Fixed Carbon CoMposition Resistors (From 1, Grade X) 可靠度保證混合碳固定電阻器（方式１之等級Ｘ） |
Translated |
|
|
CNS 11993
2017 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件ＦＯＴＰ–５０） |
|
|
|
CNS 12558
2017 Edition Method of Test for Solar Water Heater System (Automatic Cycle) 自然循環式太陽能熱水系統檢驗法 |
|
|
|
CNS 11905
2017 Edition Method of Test for Fiber Optic Devices (FOTP-83 Cable to Interconnecting Device Axial Compressive Loading) 光纖裝置檢驗法（光纜至連接器之軸向壓力負載ＦＯＴＰ–８３） |
|
|
|
CNS 4895
2017 Edition Accuracy Inspection of Hack Sawing Machines 弓鋸機精度檢驗標準 |
Translated |
|
|
CNS 10726
2017 Edition Method of Test for Printing Ink Permeation of Paper (Castor Oil Test) 紙張之印刷油墨滲透性試驗法（蓖麻油法） |
Translated |
| Find out:12524Items | To Page of: First -Previous-Next -Last | [284] [285] [286] [287] [288] [289] [290] |
