"F " CNS Standards List |
|
CNS 4364
2017 Edition Hexagon Head Fitting Bolts with Long Threaded Portion 六角頭配合螺栓（具長螺紋部份） |
|
|
|
CNS 12265
2017 Edition Method oF Test for Aluminum Tri - Polyphosphate for Coating 塗料用三聚磷酸鋁檢驗法 |
|
|
|
CNS 4877
2017 Edition Method oF Test for Pointer Type Voltmeters 指針型電壓計檢驗法 |
|
|
|
CNS 4608
2017 Edition Studs For Welding 螺樁（熔接用） |
|
|
|
CNS 13143
2017 Edition Method oF Test for Internal Bonding Strength Paperboard ( Using Z- direction Tensile / Compression Tester) 紙板內部結合強度試驗法（使用Ｚ–方向拉／壓式試驗機） |
Translated |
|
|
CNS 14489
2017 Edition Manipulating industrial robots-Presentation oF characteristics 工業用機器人-特性之標示 |
|
|
|
CNS 14685
2017 Edition Pulps - Preparation oF laboratory sheets for measurement of reflectance 紙漿、紙及紙板表示性能之國際單位 |
|
|
|
CNS 4662
2017 Edition Open Insert Nuts For Plastics Mouldings 嵌入螺帽（嵌於塑膠製品內） |
|
|
|
CNS 1189
2017 Edition HalF-round File for Carpenter, Wide Flat End 木工用闊平頭扁圓銼 |
Translated |
|
|
CNS 12994
2017 Edition Method oF Determination for total Carbon Content of Hardmetals (Gravimetric Method) 超硬合金全碳量測定法（重量法） |
|
|
|
CNS 13055
2017 Edition Methods oF Determination for Zisconium in Magnesium Alloys 鎂合金中鋯定量法 |
|
|
|
CNS 11934
2017 Edition Stop Bolts oF Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 2514
2017 Edition Method oF Test for Fiber Composition of Pulp and Paper 紙漿及紙之纖維組成試驗法 |
|
|
|
CNS 11223
2017 Edition Methods For Chemical Analysis of Refractory Clay 耐火黏土化學分析法 |
|
|
|
CNS 508
2017 Edition Knuckle Thread (ProFiles, Nominal Sizes) 圓螺紋（螺紋輪廓基本尺寸） |
|
|
|
CNS 13811
2017 Edition Numerical-Type ReFlectors for Light Emitting Diodes 發光二極體數字型反射套板 |
|
|
|
CNS 13545
2017 Edition Acoustics - PreFerred Frequencies for Measurements 聲學量測上優選的頻率 |
|
|
|
CNS 15544-2
2017 Edition Load restraint assemblies on road vehicles - SaFety - Part 2: Web lashing made from man-made fibres 道路車輛用負載束縛組合－安全規範－第2部：人造纖維製繫帶綑綁器 |
|
|
|
CNS 5501
2017 Edition SelF - Aligning Ball Bearings: Wide Inner Race, Inner Race with Clamping Sleeve 自動對位滾珠軸承（具加寬內環及附夾緊套筒內環） |
|
|
|
CNS 16002
2017 Edition Rubber compounding ingredients − Carbon black − Determination oF specific surface area by nitrogen adsorption method − Single-point procedures 橡膠配合劑－碳黑－比表面積之氮吸附測定－單點程序 |
|
|
|
CNS 1188
2017 Edition Flat File for Carpenter, Sharp Flat End 木工用尖平頭扁平銼 |
Translated |
|
|
CNS 5216
2017 Edition Inner tubes For motorcycle tyres 機車用內胎 |
|
|
|
CNS 664
2017 Edition Method oF Test for Temperature of Transmission Shaft of Water Pumps 水泵傳動軸溫度檢驗法 |
|
|
|
CNS 12562
2017 Edition Method oF Test for Fiber Optic Devices (FOTP-103 Buffered Fiber Bend Test) 光纖裝置檢驗法（緩衝式光纖彎曲試驗ＦＯＴＰ–１０３） |
|
|
|
CNS 10693
2017 Edition Method oF Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Definition and Test Condition) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（定義、試驗條件） |
|
|
|
CNS 5284
2017 Edition Addendum ModiFication of Spur Gears in the 0.5 System, Introduction ０．５齒制正齒輪之齒廓移位 |
|
|
|
CNS 8195
2017 Edition Method oF Test for Subplate Type Solenoid Operated 4 - Port Valves (Oil - Hydraulic Use ) 液壓用副板型四通電磁操作閥檢驗法 |
|
|
|
CNS 11160
2017 Edition Octave and Third-octave Band Analyzers For Sounds and Vibrations 聲音及振動用八音度及１／３八音度頻帶分析器 |
|
|
|
CNS 5051
2017 Edition Conical Spring Washers For Screw Assemblies 皿型彈簧墊圈（帶墊螺釘用） |
|
|
|
CNS 4698
2017 Edition Countersunk Double-rib Bolts and Counter Sinkings For Agricultural Equipment 平頂埋頭雙肋螺栓與錐坑（農業機械用） |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [283] [284] [285] [286] [287] [288] [289] |
