"d " CNS Standards List| Method Chemical | Synchronous digital | Tip Diameter | Method test | Electrotechnical products | Methods Test | Information technology | Cross Recessed | |
|
CNS 323
2017 Edition Hand Crank, Straight 直搖柄 |
|
|
|
CNS 5052
2017 Edition Single Coil Spring Lock Washers for Cylindrical Head Screws 單圈彈簧墊圈（柱頭螺釘用） |
|
|
|
CNS 1477
2017 Edition Viscose Rayon Staple Fiber Woven Fabrics (Finished) 黏液嫘縈棉梭織物（漂染後） |
Translated |
|
|
CNS 322
2017 Edition Hand Crank, Curved 彎搖柄 |
|
|
|
CNS 4432
2017 Edition Slotted Round Nuts 頂槽圓螺帽 |
|
|
|
CNS 5653
2017 Edition Method of Test for Level Gauge 水平儀檢驗法 |
|
|
|
CNS 15513
2017 Edition Electric road vehicles – Reference energy consumption and range – Test procedures for passenger cars and light commercial vehicles 電動道路車輛－電能消耗與行駛距離－小客車與商用車試驗程序 |
|
|
|
CNS 11399
2017 Edition Method of Straight-Beam Ultrasonic Test for Steel Plate for Pressure Vessel Use 壓力容器用鋼板直束法超音波檢驗法 |
|
|
|
CNS 12865-9
2017 Edition Method of Test for Digital Microelectronics ( Delay Measurements ) 數位微電子檢驗法（延遲量測） |
|
|
|
CNS 15210-6
2017 Edition Information technology - Radio frequency identification for item management - Part 6: Parameters for air interface communications at 860MHz to 960MHz 資訊技術─品項管理之無線射頻識別─第６部：８６０ＭＨｚ至９６０ＭＨｚ空中介面通信參數 |
|
|
|
CNS 12292
2017 Edition Reliability Assured Fixed Carbon Composition Resistors (Established Failure Rate) 可靠度保證混合碳固定電阻器（故障率設定） |
Translated |
|
|
CNS 12296
2017 Edition Reliability Assured Power Type Fixed Wire Wound Resistors (S) (Established Failure Rate) 可靠度保證功率型線繞固定電阻器（特性Ｓ）（故障率設定） |
Translated |
|
|
CNS 8874
2017 Edition detector of fire alarm equipment 火警探測器 |
Translated |
|
|
CNS 8876
2017 Edition Fire manual station and its fire alarm bell indication lamp 火警發信機及其火警警鈴、標示燈 |
Translated |
|
|
CNS 13622
2017 Edition Fixed chip resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 14382
2017 Edition Protective gloces against chemicals and micro-organisms - Part 3:Determination of resistance to permeation by chemicals 防護手套－一般要求及試驗方法 |
|
|
|
CNS 3470
2017 Edition Method of Test for Power Cultivator 動力中耕除草機檢驗法 |
|
|
|
CNS 715
2017 Edition Cast Iron Flanged Gate Valves ( 10 kgf/㎠) ( Outside Screw Type) 鑄鐵凸緣型閘閥（10 kgf/㎠）（閥桿上升型） |
Translated |
|
|
CNS 10541
2017 Edition Test Code for Performance of Wood Borers and Hollow Chisel Motisers 木工鑽及角鑿機動態檢驗法 |
|
|
|
CNS 5153
2017 Edition Photography-Processing chemicals-Specifications for potassium bromide 照相術─顯像處理化學品─溴化鉀規格 |
|
|
|
CNS 8480
2017 Edition Hydraulic Clutch Master Cylinder for Automobiles 汽車用液壓離合器總泵 |
Translated |
|
|
CNS 4731
2017 Edition Knurled Nuts for Drawing Instruments 滾紋螺帽（製圖儀器用） |
|
|
|
CNS 13004
2017 Edition Method of Welding Procedure Qualification Test for Stainless-clad steels 不銹鋼包層鋼板熔接施工程序確認試驗法 |
|
|
|
CNS 13252
2017 Edition Method of Tension Test for Spot Welded Joints 點熔接接合之拉伸試驗法 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 14447
2017 Edition Method of measurement for glossiness on surface of ornamental stone 天然飾面石材表面光澤度測定法 |
|
|
|
CNS 12895
2017 Edition Rubber Hose Connections for Welding and Cutting Equipment 熔接與截割器（切斷器）用橡皮軟管接頭 |
|
|
|
CNS 11393
2017 Edition Methods of Chemical Analysis for Limestone 石灰石化學分析法 |
|
|
|
CNS 10681
2017 Edition Saw Blades for Woodworking Crosscut Saws 木工用橫切鋸鋸片 |
|
|
|
CNS 3497
2017 Edition Canned tomatoes 番茄罐頭 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [280] [281] [282] [283] [284] [285] [286] |
