"f " CNS Standards List |
|
CNS 502
2017 Edition ISO Metric fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 5671
2017 Edition Arbor Bearing Collars for Milling Machines 銑刀心軸軸承軸環 |
|
|
|
CNS 6546
2017 Edition Guide Pins of Molds for Plastics 塑膠型模用導銷 |
|
|
|
CNS 7197
2017 Edition Basic Dimensions of 5 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（5 kgf/㎠） |
|
|
|
CNS 61591
2017 Edition Household range hoods and other cooking fume extractors − Methods for measuring performance 家用抽油煙機及其他烹煮油煙抽取器之性能量測法 |
|
|
|
CNS 15968
2017 Edition Plastics − film and sheeting − Measurement of water-contact angle of corona-treated films 塑膠－薄膜及薄片－電暈處理薄膜水接觸角量測法 |
|
|
|
CNS 3886
2017 Edition Heat Treatment of Bicycle Parts 自行車（腳踏車）零件熱處理 |
Translated |
|
|
CNS 5968
2017 Edition Bronze Screwed Lift Check Valves (10kgf/c㎡) 青銅螺紋口升降型止回閥（10 kgf/㎠） |
|
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 4646
2017 Edition Square Taper Washers for High Prestressed I-Sections 斜墊圈（工字鐵高強度結構用） |
|
|
|
CNS 12886-1
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Dry Heat Treatment at 120℃ or 150℃ 紙及紙板加速老化試驗法─120℃或150℃乾熱處理 |
Translated |
|
|
CNS 12435
2017 Edition Pressure Sensitive Aluminum foil Abrasive Tape for Non-Slip 電絕緣用聚酯膜黏帶 |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 3873
2017 Edition Method of Test for the Rear Hubs of Bicycles 自行車（腳踏車）後輪轂檢驗法 |
Translated |
|
|
CNS 4559
2017 Edition Cross Recessed Raised fillister Head Screws 十字穴扁圓頂柱頭螺釘 |
Translated |
|
|
CNS 1195
2017 Edition flat File for Smith, Sharp Flat End 鐵工用尖平頭扁平銼 |
Translated |
|
|
CNS 4421
2017 Edition Seating Bolts and Conical Spring Washers for Clamping 夾緊用座螺栓與錐形彈簧墊圈 |
|
|
|
CNS 5
2017 Edition Trimmed Sizes of Writing and Printing Paper 紙張尺度（裁切後） |
Translated |
|
|
CNS 12256
2017 Edition Ovens for Quartz Crystal Units 石英振盪晶體用恆溫箱 |
|
|
|
CNS 3441
2017 Edition Method of test for milk and milk products - Titration of acidity 乳品檢驗法－酸度之滴定 |
Translated |
|
|
CNS 3957
2017 Edition Method of Test for Vinylon Sewing Thread 維尼龍縫線檢驗法 |
|
|
|
CNS 8919
2017 Edition Auxiliaries of Stationary Centrifugal Fire Pumps 固定式消防用加壓離心泵之附屬裝置 |
|
|
|
CNS 4693
2017 Edition fish Bolts with Round Head and Oval Neck 魚尾板螺栓（具圓頭橢圓頸） |
|
|
|
CNS 11942-5
2017 Edition Methods for determination of manganese in copper and copper alloys 銅及銅合金中錳定量法 |
|
|
|
CNS 4487
2017 Edition Method of test for surface discontinuities –Bolts, screws and studs for general requirements 螺釘表面瑕疵檢驗法 |
|
|
|
CNS 5158
2017 Edition Dimensions for 127, 120 and 620 Roll Film, Backing Paper and Film Spools １２７、１２０及６２０捲裝軟片背紙與軟片軸之尺度 |
|
|
|
CNS 4790-5
2017 Edition Glossary of terms used in pulp and paper industry ─ Terms of pulp, paper or board properties 紙漿與紙詞彙─紙漿、紙或紙板之性質及試驗名詞 |
|
|
|
CNS 10114
2017 Edition Method for Determining Iron Content in Natural and Artificial Cryolite (1,10-Phenanthroline Photometric Method) 天然及人造冰晶石中鐵定量法（二氮雜菲吸光光度法） |
|
|
|
CNS 4560
2017 Edition Cross Recessed Countersunk (flat) Head Screws 十字穴平頂埋頭螺釘 |
Translated |
|
|
CNS 13004
2017 Edition Method of Welding Procedure Qualification Test for Stainless-clad steels 不銹鋼包層鋼板熔接施工程序確認試驗法 |
|
| Find out:12815Items | To Page of: First -Previous-Next -Last | [266] [267] [268] [269] [270] [271] [272] |
