"an " CNS Standards List| Specified Items | Plastics − | Methods determination | Scupper Fitting | Sanitary ceramic | Acoustics | Method Test | Method Test | |
|
CNS 15793
2021 Edition The enzymatic method for fresh chilled and thawed frozen chicken meat 冷藏與冷凍後解凍雞肉酵素活性檢驗法 |
|
|
|
CNS 12491-4
2021 Edition Graphical Symbols for Use on Electrical and Electronic Equipment (Alarm,Signal,Filter) 電機電子設備用圖符號（警報，信號，濾波器） |
|
|
|
CNS 16890-2
2021 Edition Air filters for general ventilation − Part 2: Measurement of fractional efficiency and air flow resistance 一般通風用空氣濾網－第2部：區間效率與空氣流阻抗之量測 |
|
|
|
CNS 8314
2021 Edition Oilseeds - Reduction of Contract Samples to analysis Samples 油籽–契約樣品之縮減至分析樣品 |
Translated |
|
|
CNS 10880-27
2021 Edition Method of Test for Paint Components-Quantitative Test of Zinc Oxide in Solvent Insolubles 塗料成分檢驗法–溶劑不溶物中氧化鋅之定量試驗 |
|
|
|
CNS 13605
2021 Edition Method of test for gas burning appliances of domestic use 家庭用燃氣器具試驗法 |
Translated |
|
|
CNS 8776
2021 Edition Taper Pins with Thread and Constant Taper Length 推拔銷（有螺紋及一定之推拔長） |
|
|
|
CNS 15160-7
2021 Edition Acoustics - Measurement of sound insulation in buildings and of building elements - Field measurements of impact sound insulation of floors 聲學－建築物及建築構件之隔音量測法－樓板衝擊音隔音之現場量測方法 |
|
|
|
CNS 15946
2021 Edition Information technology − Procedure for registration of escape sequences and coded character sets 資訊技術－逸出序列及編碼字元集之登錄程序 |
|
|
|
CNS 15860
2021 Edition Plastics pipes and fittings − Preparation of polyethylene (PE) pipe/pipe or pipe/fitting test piece assemblies by butt fusion 塑膠管及管件－聚乙烯(PE)管及電熔接管件組裝試件之製備 |
|
|
|
CNS 15372
2021 Edition Method of test for total volatile sulfur in gaseous hydrocarbons and liquefied petroleum gases by ultraviolet fluorescence 氣態碳氫化合物、液化石油氣總揮發性硫含量紫外線螢光試驗法 |
|
|
|
CNS 3687
2021 Edition Method of test for water repellency of paper and board 紙及紙板撥水度試驗法 |
|
|
|
CNS 301
2021 Edition Hand Tap, Whitworth 韋氏絲公，手用 |
|
|
|
CNS 3220-4
2021 Edition Sanitary ceramic ware – Kitchen sink 衛生陶瓷器–廚房洗滌槽 |
Translated |
|
|
CNS 793
2021 Edition Basic Dimensions of 40 kgf/㎠ Steel Pipe Flanges 鋼製管凸緣基準尺度（40 kgf/㎠） |
|
|
|
CNS 3641
2021 Edition Method of test for edible oils and fats－Color test 食用油脂檢驗法－顏色之測定 |
|
|
|
CNS 12354
2021 Edition Contrast of Wire Gauge to Diameter and Section Area 線規與公制直徑及有效截面積對照表 |
|
|
|
CNS 11443
2021 Edition Tolerance of the Combined Indicator and the Driving Elements 驅動裝置及綜合表示誤差容許限度 |
|
|
|
CNS 11942-3
2021 Edition Methods for determination of lead in copper and copper alloys 銅及銅合金中鉛定量法 |
|
|
|
CNS 2815
2021 Edition Salted Mei (Japanese apricot) 鹽醃梅 |
|
|
|
CNS 10880-17
2021 Edition Method of Test for Paint Components-Quantitative Test of Phosphoric Acid 塗料成分檢驗法–磷酸之定量 |
|
|
|
CNS 1280
2021 Edition Leather - Physical and mechanical tests - Determination of shrinkage temperature up to 100℃ 皮革－物性及機械性能測試－100℃以下熱收縮溫度試驗法 |
|
|
|
CNS 792
2021 Edition Basic Dimensions of 20 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（20 kgf/㎠） |
|
|
|
CNS 794
2021 Edition Basic Dimensions of 63 kgf/㎠ Steel Pipe Flanges 鋼製管凸緣基準尺度（63 kgf/㎠） |
|
|
|
CNS 11256
2021 Edition Specification of Colours According to the CIE 1931 Standard Colorimetric System and the CIE 1964 Supplementary Standard Colorimetric System ＸＹＺ表色系及X10Y10Z10表色系之顏色表示法 |
|
|
|
CNS 15408-1
2021 Edition Information security, cybersecurity and privacy protection − Evaluation criteria for IT security − Part 1: Introduction and general model 資訊安全、網宇安全及隱私保護－IT安全之評估準則－第1部：簡介及一般模型 |
|
|
|
CNS 15814-2
2021 Edition Fire tests for building elements and components – Fire testing of service installations – Part 2: Linear joint (gap) seals 建築構件與零組件防火試驗－ 配管設置防火測試－ 第2 部：線形接合(縫隙)密封部 |
|
|
|
CNS 60335-2-17
2021 Edition Household and similar electrical appliances − Safety − Part 2-17: Particular requirements for blankets, pads, clothing and similar flexible heating appliances 家用和類似用途電器－安全性－第2-17 部： 電熱毯、電熱墊、電熱衣及類似可撓式加熱電器之個別規定 |
|
|
|
CNS 15807
2021 Edition Intelligent transport systems − Communications access for land mobiles (CALM) − Architecture 智慧型運輸系統－陸地行動通訊接取(CALM)－架構 |
|
|
|
CNS 13629
2021 Edition Polybutylene (PB) plastics piping systems for hot and cold water installations - Part 7: Guidance for the assessment of conformity 聚碳酸酯成形材料 |
Translated |
| Find out:7408Items | To Page of: First -Previous-Next -Last | [22] [23] [24] [25] [26] [27] [28] |
