"fo " CNS Standards List |
|
CNS 14385
2012 Edition Conformity assessment - Code of good practice 符合性評鑑－良好作業規範 |
|
|
|
CNS 15581
2012 Edition Grading rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 15620-1
2012 Edition Insulation coordination for equipment within low-voltage system – Part 1: Principles, requirements and tests 低電壓系統下設備之絕緣協調－第1部：原理、要求及試驗 |
|
|
|
CNS 15625-1
2012 Edition Paragliding equipment – Paragliders – Part 1: Requirements and test methods for structural strength 飛行傘設備－飛行傘－第1部：結構強度要求與試驗法 |
|
|
|
CNS 15625-2
2012 Edition Paragliding equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics 飛行傘設備－飛行傘－第2部：飛行安全性分類要求與試驗法 |
|
|
|
CNS 1217
2012 Edition Method of practice for manual sampling of petroleum and petroleum products 石油及其產品手動取樣法 |
|
|
|
CNS 14266
2012 Edition Cable management systems – Cable ties for electrical installations 電纜管理系統-電機設備用電纜束線帶 |
|
|
|
CNS 444
2012 Edition Grading rules for sawn lumber 製材之分等 |
|
|
|
CNS 11984
2012 Edition Steel furrings for wall and ceiling in buildings 建築用暗架式牆壁及平頂輕鋼架 |
|
|
|
CNS 14866-2
2012 Edition Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 4626
2012 Edition Carbon steel pipes for pressure service 壓力配管用碳鋼鋼管 |
|
|
|
CNS 14400
2012 Edition Low-voltage three-phase squirrel-cage high-efficiency induction motors (for general purpose) 低壓三相鼠籠型高效率感應電動機(一般用) |
Translated |
|
|
CNS 5802
2012 Edition Stainless steel tubes for machine and structural purposes 機械結構用不銹鋼鋼管 |
|
|
|
CNS 15604
2012 Edition Corrugated stainless steel tubes for water supply 自來水用不銹鋼波狀管 |
Translated |
|
|
CNS 2598
2012 Edition Charcoal for fuel use 木炭(燃料用) |
|
|
|
CNS 15628-1
2012 Edition Wheelchair seating - Part 1: Vocabulary, reference axis convention and measures for body segments, posture and postural support surfaces 輪椅乘坐系統－第1部：詞彙、參考軸協定及身體肢段、姿勢與姿勢支撐面之量測 |
|
|
|
CNS 9621-3
2012 Edition Rubber hoses for liquefied petroleum gases (LPGs) - Part 3: Dispensing hoses and hose assemblies 液化石油氣用橡膠管(LPG橡膠管)－第3部:加氣用管及管組合件 |
|
|
|
CNS 15570
2012 Edition Petroleum products - Determination of aromatic hydrocarbon types in middle distillates - High performance liquid chromatography method (non-backflush) with refractive index detection 石油產品－中質蒸餾燃油芳香烴類別含量測定法[高效液相層析(非逆洗)/折射率偵檢法] |
|
|
|
CNS 4745
2012 Edition Copper rod drawing stock for electrical purposes 電氣用抽製銅條 |
|
|
|
CNS 4196
2012 Edition General rules for sampling, sample preparation and analytical testing of non-ferrous metals 非鐵金屬材料之試樣採取、製備及分析檢驗通則 |
|
|
|
CNS 386-1
2012 Edition Test sieves - for construction engineering 試驗篩-營建工程用 |
|
|
|
CNS 15544-1
2012 Edition Load restraint assemblies on road vehicles - Safety - Part 1: Calculation of lashing forces 道路車輛用負載束縛組合－安全規範－第1部：綑綁力之計算 |
|
|
|
CNS 13249
2012 Edition Conformity assessment - Guidance on a third-party certification system for products 符合性評鑑－第三者產品驗證系統指引 |
|
|
|
CNS 9969
2012 Edition Safety devices for protection against excessive pressure - Part 1: Safety valves 防止超壓之安全裝置－第1部：安全閥 |
|
|
|
CNS 6834-8
2012 Edition Testing methods for rubber and plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 13133
2012 Edition Glossary of terms used in building sealant for joint 建築用接合密封材料用語 |
|
|
|
CNS 9504
2012 Edition Methods for estimating average grain size of wrought copper and copper alloys 銅及銅合金展伸材料之晶粒尺度測定法 |
|
|
|
CNS 15537
2012 Edition Determination of the indoor thermal comfort environment 室內環境熱舒適度量測法 |
|
|
|
CNS 15077-10
2012 Edition Test conditions for machining centres - Part 10: Evaluation of thermal distortions 切削中心機之檢驗條件－第10部：熱變形之評估 |
|
|
|
CNS 552
2012 Edition Pencil, coloured pencils and leads for them 鉛筆、顏色鉛筆及其筆芯 |
|
| Find out:9692Items | To Page of: First -Previous-Next -Last | [259] [260] [261] [262] [263] [264] [265] |
