"c " CNS Standards List |
|
CNS 4534
2018 Edition Terms of fasteners for screws,bolts,studs 結件詞彙（螺釘、螺栓、螺樁） |
|
|
|
CNS 2358
2018 Edition Method of Test for Nitrocellulose for Industrial Use 工業用硝化纖維素檢驗法 |
Translated |
|
|
CNS 12993
2018 Edition Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency 包裝貨物與單位裝載之固定低頻率振動試驗法 |
|
|
|
CNS 27004
2018 Edition Information technology − Security techniques − Information security management − Measurement 資訊技術－安全技術－資訊安全管理－量測 |
|
|
|
CNS 10435
2018 Edition Steel cargo Block with Roller Bearings for Marine Use 船舶吊貨用鋼滑車（附滾子軸承） |
|
|
|
CNS 14172
2018 Edition ATM cell mapping into plesiochronous digital hierarchy (PDH) 非同步傳送模式細胞與近同步數位階層之對映 |
|
|
|
CNS 13662
2018 Edition Implementation Requirement Specification Connectionless Network Service Protocols for the use by FTAM 檔案轉送、存取及管理用免接式網路服務通訊協定之實作需求規範 |
|
|
|
CNS 12396
2018 Edition Signal Quality at Interface Between Data Terminal Equipment and Synchronous Data Circuit-Terminating Equipment for Serial Data Transmission 串列資料傳輸用資料終端設備與同步資料電路終端設備間介面上之信號品質 |
|
|
|
CNS 16040
2018 Edition Footwear − Performance requirements for components for footwear − Accessories 鞋類－鞋類組件性能要求－配件 |
|
|
|
CNS 14980-2-2
2018 Edition Appliance couplers for household and similar general purposes - Part 2-2: Interconnection couplers for household and similar equipment 家用和類似一般用途之電器耦合器－第２－２部：家用和類似用途設備之互連式耦合器 |
|
|
|
CNS 14168-1
2018 Edition Information technology - Framework and taxonomy of International Standardized Profiles - Part 1: General principles and documentation framework 資訊技術–國際標準規範之框架及分類–第１部：一般原則及文件框架 |
|
|
|
CNS 14515
2018 Edition colour coded polyethylene insulated laminated aluminum polyethylene sheathed cables 彩色聚乙烯絕緣積層被覆（ＣＣＰ－ＬＡＰ）市內電纜 |
|
|
|
CNS 11994
2018 Edition cable Clamping Devices for Motor Starters and Controllers in Ships 船用電動機起動器及控制器之電纜固定方法 |
|
|
|
CNS 15091-24
2018 Edition Method of test for deep sea water - Determination of strontium 深層海水檢驗法－鍶之測定 |
|
|
|
CNS 13700
2018 Edition Method for the characterization of Telecommunication Services Supported by an Integrated Services Digital Network (ISDN) and Network Capabilities of an ISDN 整體服務數位網路與其網路能力的電信服務之特性描述方法 |
|
|
|
CNS 14964-15
2018 Edition Wheelchairs - Part 15 : Requirements for information disclosure, documentation and labelling 輪椅－第１５部：資訊宣告、文件與標示之要求 |
|
|
|
CNS 6197
2018 Edition Determination of Moisture content of Sodium Chlorate for Industrial Use(Gravimetric Method) 工業用氯酸鈉水分測定法（重量分析法） |
|
|
|
CNS 15405
2018 Edition Roasted ground coffee − Determination of moisture content − Karl Fischer method (Reference method) 焙製磨碎咖啡－水分測定－卡爾費雪法(參考法) |
|
|
|
CNS 13797
2018 Edition General Aspects and Principles Relating to Recommendations on ISDN User-Network Interfaces 整體服務數位網路用戶與網路間介面概觀與原則 |
|
|
|
CNS 14855-1
2018 Edition Prferred Numbers--Series of Preferred Number 一次電池－第１部：通則 |
|
|
|
CNS 13934
2018 Edition characteristics of synchronous digital hierarchy (SDH) multiplexing equipment functional blocks 同步數位階層多工設備功能方塊的特性 |
|
|
|
CNS 13918
2018 Edition Basic parameters for the measurement of error performance at bit rates below the primary rate 位元速率低於原級速率之錯誤性能測量基本參數 |
|
|
|
CNS 9698
2018 Edition Jumper couplers 電氣連結器 |
|
|
|
CNS 16000-23
2018 Edition Indoor air – Part 23: Performance test for evaluating the reduction of formaldehyde concentrations by sorptive building materials 室內空氣－第23部：評估吸附/吸收性建築材料降低甲醛濃度之性能試驗 |
|
|
|
CNS 2301
2018 Edition Method of test for frozen shrimp 冷凍蝦類檢驗法 |
Translated |
|
|
CNS 8204
2018 Edition Deep groove ball bearings,single-row without filling notch, with tapered bore 徑向深溝滾珠軸承－單列、無填裝槽、具推拔孔 |
|
|
|
CNS 13360
2018 Edition Data communication - 34 Pin DTE/DCE Interface Connector and pin Assignments 數據通訊–３４插腳ＤＴＥ／ＤＣＥ介面連接器及插腳配置 |
|
|
|
CNS 10802
2018 Edition Single-Start and Double-Start Trapezoidal Screw Thread with Clearance for Railway Rolling Stock (Theoretical Values) 鐵路車輛用單頭與雙頭梯形螺紋（理論值） |
|
|
|
CNS 10080
2018 Edition Marine Section Boards (Circuit Breaker Type, Below 250 V) 船用區電箱（斷路器型，２５０Ｖ以下） |
|
|
|
CNS 15565-1
2018 Edition Ergonomic design for the safety of machinery – Part 1: Principles for determining the dimensions required for openings for whole-body access into machinery 機械安全之人因工程設計－第1部：人員全身進入機械內 的開口所需尺度之決定原則 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [258] [259] [260] [261] [262] [263] [264] |
