"D " CNS Standards List |
|
CNS 13191
2017 Edition Test MethoDs for Performance and Accuracy of Band Saws 木工帶鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 11158
2017 Edition Tungsten-CarbiDe Bits and Rod for Rock Drill Sets 鑽石用碳化鎢鑽刃及鑽桿組 |
|
|
|
CNS 14866-3
2017 Edition Measurement of water flow in fully chargeD closed conduits − Meters for cold potable water and hot water − Part 3: Test methods and equipment 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第3部：試驗法及裝備 |
|
|
|
CNS 9371
2017 Edition MethoD of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 39 Hydrostatic Test) 頻率３ＭＨｚ以下電連接器檢驗法（流體靜壓力試驗ＴＰ–３９） |
|
|
|
CNS 523
2017 Edition Plug Connection Devices for Explosion-Proof Type Battery Locomotives 韋氏螺紋量柱（通過端限界尺寸、精配、中配及粗配） |
|
|
|
CNS 11765
2017 Edition MethoD of Test for Magnetic Sound Recording Tapes 磁性錄音帶檢驗法 |
|
|
|
CNS 14741
2017 Edition Diaphragm type gas meter with micro computers for nature gas use 天然氣用微電腦膜式氣量計 |
|
|
|
CNS 15558-2
2017 Edition Flexible cellular polymeric materials - Physical properties - Part 2: Determination of hardness (indentation technique), compressive deflection coefficient, hysteresis loss rate and stress/strain characteristic in compression 軟質發泡材料－物理特性－第２部：硬度(凹壓法)、壓縮撓度係數、遲滯損失率及壓縮應力/應變特性測定法 |
|
|
|
CNS 13350-10
2017 Edition The Safety CoDe of Mechanical Parking Lot Devices (Elevator Sliding Type) 機械式停車場安全標準（升降滑動式） |
|
|
|
CNS 6412
2017 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算–螺旋角因數Ｙᵦ |
|
|
|
CNS 2943
2017 Edition ScreweD Type Malleable Cast Iron Pipe Fittings 螺紋式展性鑄鐵管件 |
Translated |
|
|
CNS 715
2017 Edition Cast Iron FlangeD Gate Valves ( 10 kgf/㎠) ( Outside Screw Type) 鑄鐵凸緣型閘閥（10 kgf/㎠）（閥桿上升型） |
Translated |
|
|
CNS 11446-3
2017 Edition MethoDs of measurement on receivers for television broadcast transmissions - Part 3 : Electrical measurement on multichannel sound television receivers using subcarrier systems 電視廣播傳輸接收機之量測方法-第3部 : 利用副載波系統之多聲道電視接收機之電氣量測 |
|
|
|
CNS 12744
2017 Edition Wafer-Type Rubber-SeateD Butterfly Valves 一般用蝶型閥 |
|
|
|
CNS 6834-7
2017 Edition Testing methoDs for rubber and plastics hoses - Part 7: Assessment of ozone resistance under static conditions 橡膠管及塑膠管試驗法－第7部：靜態狀況下耐臭氧性之評估 |
|
|
|
CNS 12596
2017 Edition ADhesives for resilient floorcoverings and woody floorings 地板鋪設材用接著劑 |
|
|
|
CNS 15551-1
2017 Edition Ergonomics - Accessible Design - Auditory signals for consumer products 人因工程－無障礙設計 - 消費產品之聲音訊號 |
|
|
|
CNS 7797
2017 Edition Thermal spraying - Zinc, aluminum anD their alloys 鋅、鋁及其合金之熔射 |
|
|
|
CNS 8785
2017 Edition MethoD of Test for Electric Strength of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管絕緣強度試驗法 |
|
|
|
CNS 14535
2017 Edition MethoD of test for flammability of plastic material 塑膠材料燃燒試驗法 |
Translated |
|
|
CNS 6411
2017 Edition Calculation of LoaD Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算–接觸比因數Zε |
|
|
|
CNS 6761
2017 Edition Parallel Shank Core Drills of High - Speed Steel 高速鋼製取心鑽（圓柱柄） |
|
|
|
CNS 13923
2017 Edition MethoD of test for thickness of plastic film and sheeting 塑膠薄膜及薄片之厚度試驗法 |
|
|
|
CNS 11901
2017 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 13119
2017 Edition MethoD of test for coefficient of static friction of paper and paperboard(Inclined plane method and horizontal plane method) 紙及紙板靜摩擦係數試驗法(傾斜平面法及水平平面法) |
|
|
|
CNS 304
2017 Edition HanD Taps, Metric (Two Pieces Per Set) 公制絲公，手用，每套兩件 |
Translated |
|
|
CNS 13086
2017 Edition Basic Environmental Testing proceDures Part 2: Test Td: Solderability.resistance to dissolution of Metallization and to Soldering Heat of Surface Mounting Devices (SMD) 環境試驗法（電氣、電子）–表面黏著元件之焊錫性，金屬端的耐溶解性及焊錫耐熱性 |
|
|
|
CNS 12848
2017 Edition NoDular Graphite Iron Screwed Globe Valves (10 kgf/㎠) 球狀石墨鑄鐵螺紋口球形閥（10 kgf/㎠） |
Translated |
|
|
CNS 6304
2017 Edition Running Inspection MethoD of Band Saw Mills and Their Feed Carriages 帶鋸機及其進給溜板之運轉檢驗法 |
|
|
|
CNS 15564-4
2017 Edition ISO general purpose metric screw threaDs - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing ISO一般用途公制螺紋－公差－第4部：鍍鋅後依公差位置H或G攻牙之內螺紋相配合的熱浸鋅外螺紋之限界尺度 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [255] [256] [257] [258] [259] [260] [261] |
