"H " CNS Standards List |
|
CNS 3509
2017 Edition Covered Electrodes for Hardfacing 硬面銲被覆銲條 |
Translated |
|
|
CNS 5774
2017 Edition THermistor Rods, Insulated (Style TRC) 管形絕緣熱敏電阻器（型號ＴＲＣ） |
|
|
|
CNS 5665
2017 Edition Test Code for Performance of UprigHt Drilling Machines 直立鑽床動態檢驗法 |
|
|
|
CNS 11168
2017 Edition Iron and steel – MetHods for determination of cobalt content 鐵及鋼－鈷定量法 |
|
|
|
CNS 5148
2017 Edition PHotography-Camera accessory shoes ,with and without electrical contact , for photoflash lamps and electronic photoflash units 照相術─照相機閃光燈附件靴座 |
|
|
|
CNS 9796
2017 Edition Saddle supported Horizontal pressure vessels 以鞍座支撐之臥型壓力容器 |
|
|
|
CNS 4664
2017 Edition Closed Insert Nuts witH Dead Hole for Plastics Mouldings 嵌入螺帽（封閉式，嵌於塑膠製品內） |
Translated |
|
|
CNS 13378
2017 Edition Boron Steel Wires for Cold Heading and Cold Forging 冷打及冷鍛用硼鋼鋼線 |
|
|
|
CNS 5284
2017 Edition Addendum Modification of Spur Gears in tHe 0.5 System, Introduction ０．５齒制正齒輪之齒廓移位 |
|
|
|
CNS 14136
2017 Edition MetHod of ultrasonic test for steel forgings 鍛鋼品超音波檢測法 |
|
|
|
CNS 4096
2017 Edition CHucks for Portable Electric Drills 手提電鑽用夾頭 |
Translated |
|
|
CNS 60227-1
2017 Edition Polyvinyl cHloride insulated cables of rated voltages up to and including 450/750V − Part 1: General requirements 額定電壓450/750 V以下聚氯乙烯絕緣電纜－第1 部：一般要求 |
|
|
|
CNS 14818
2017 Edition MetHod of test for density of smoke generated by solid materials -Specificoptical method of vertical type 固體材料燃燒煙濃度試驗法－比光學密度垂直試驗法 |
|
|
|
CNS 13624
2017 Edition Test MetHods for Crystallographic Perfection of Gallium Arsenside by Molten Potassium Hydroxide(KOH)Etch Technique 砷化鎵晶體結晶完整性檢驗法（熔融氫氧化鉀浸蝕法） |
|
|
|
CNS 15975
2017 Edition Accessible design − Guidelines for operability of vending macHine 無障礙設計－自動販賣機操作性指導綱要 |
|
|
|
CNS 13595
2017 Edition MetHods of Test for Several Characteristics of Textile Floor Coverings 纖維製地毯類織物之性能試驗法 |
|
|
|
CNS 4766
2017 Edition MetHod of copper sulfate-sulfuric acid test for stainless steel 不銹鋼之硫酸銅—硫酸溶液腐蝕試驗法 |
|
|
|
CNS 366-9
2017 Edition Safety requirements for cycles − Part 9: Saddles and seat-post test metHods 自行車安全要求－第9部：座墊及座桿測試法 |
|
|
|
CNS 15986-5
2017 Edition Quality requirements for fusion welding of metallic materials − Part 5: Documents witH which it is necessary to conform to claim conformity to the quality requirements of CNS 15986-2, CNS 15986-3 or CNS 15986-4 金屬材料熔融銲接的品質要求－第5部：宣告符合CNS 15986-2、CNS 15986-3或CNS 15986-4時應符合之文件 |
|
|
|
CNS 664
2017 Edition MetHod of Test for Temperature of Transmission Shaft of Water Pumps 水泵傳動軸溫度檢驗法 |
|
|
|
CNS 13622
2017 Edition Fixed cHip resistor for use in electronic equipment 電子設備用固定晶片電阻器 |
|
|
|
CNS 4404
2017 Edition Serrated Lock WasHers 鋸齒墊圈 |
|
|
|
CNS 8973
2017 Edition QuencHed and Tempered Manganese-Molybdenum and Manganese-Molybdenum-Nickel Alloy Steel Plates for Pressure Vessels 壓力容器用淬火–回火之錳鉬及錳鉬鎳合金鋼鋼板 |
|
|
|
CNS 7777
2017 Edition Accuracy Inspection of BencH Lathes 枱式車床精度檢驗標準 |
|
|
|
CNS 14492-6
2017 Edition MetHods of measurement on radio receivers for various classes of emission -Part 6：General purpose communication receivers 不同發射類別之無線電接收機的量測方法─第６部：一般用途通訊接收機 |
|
|
|
CNS 7962
2017 Edition Test Code for Performance of Numerically Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 10673
2017 Edition Cubicle Emergency Power Source for Fire FigHting Use 消防用櫃式緊急電源受電設備 |
Translated |
|
|
CNS 7748
2017 Edition MetHod of Test for Viscosity of Pulp ( Cannon -Fenske Capillary Viscometer Method ) 紙漿黏度試驗法（Ｃａｎｎｏｎ–Ｆｅｎｓｋｅ毛細管黏度計法） |
Translated |
|
|
CNS 6762
2017 Edition Morse Taper SHank Core Drills of High Speed Steel 高速鋼製取心鑽（莫氏圓錐柄） |
|
|
|
CNS 10643
2017 Edition Curved Lip, Fluted Jaw, BlacksmitHs Tongs 鍛工用有槽顎夾夾鉗 |
|
| Find out:11384Items | To Page of: First -Previous-Next -Last | [253] [254] [255] [256] [257] [258] [259] |
