"m " CNS Standards List |
|
CNS 11709
2017 Edition method of Test for Portable/Personal Radio Transmitters, Receivers, and Transmitter/Receiver Combination Land Mobile Communications FM or PM Equipment, 25-1000 MHz 陸上行動通信用２５–１０００ＭＨｚ調頻／調相設備攜帶型／個人無線電發射機、接收機及收發信機組合檢驗法 |
|
|
|
CNS 15554
2017 Edition medical electrical equipment - Part 2-52: Particular requirements for the basic safety and essential performance of medical beds 醫電設備電性安全－第2-52部：醫護床基本安全及必要性能的特殊要求 |
|
|
|
CNS 14916
2017 Edition Retroreflective pavement marker 反光片型路面標記 |
|
|
|
CNS 4229
2017 Edition ISO metric Screw Threads-Selected Sizes for Screws, Bolts and Nuts 公制螺紋（ＩＳＯ制）（螺釘、螺栓及螺帽標稱直徑與螺距之選擇） |
|
|
|
CNS 11651
2017 Edition method of Test for Glassfiber Reinforced Plastic Electric Enclosure 玻璃纖維強化塑膠配電箱體檢驗法 |
Translated |
|
|
CNS 14300
2017 Edition Characteristics of a single-mode optical fiber 單模光纖之特性 |
|
|
|
CNS 14741
2017 Edition Diaphragm type gas meter with micro computers for nature gas use 天然氣用微電腦膜式氣量計 |
|
|
|
CNS 15507
2017 Edition Occupational health and safety management systems - Guideline 職業安全衛生管理系統－指導綱要 |
|
|
|
CNS 14511
2017 Edition Protective gloves against chemicals and micro-organisms - Part 2:Determination of resistance to penetration 機械性風險防護手套 |
|
|
|
CNS 13086
2017 Edition Basic Environmental Testing procedures Part 2: Test Td: Solderability.resistance to dissolution of Metallization and to Soldering Heat of Surface Mounting Devices (SMD) 環境試驗法（電氣、電子）–表面黏著元件之焊錫性，金屬端的耐溶解性及焊錫耐熱性 |
|
|
|
CNS 6304
2017 Edition Running Inspection method of Band Saw Mills and Their Feed Carriages 帶鋸機及其進給溜板之運轉檢驗法 |
|
|
|
CNS 9371
2017 Edition method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 39 Hydrostatic Test) 頻率３ＭＨｚ以下電連接器檢驗法（流體靜壓力試驗ＴＰ–３９） |
|
|
|
CNS 7407
2017 Edition Cellular plastics and rubbers - Determination of apparent (bulk) density 發泡塑膠及橡膠－視密度測定法 |
|
|
|
CNS 11901
2017 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 15551-1
2017 Edition Ergonomics - Accessible design - Auditory signals for consumer products 人因工程－無障礙設計 - 消費產品之聲音訊號 |
|
|
|
CNS 8697
2017 Edition Carbon Steel Plates for Pressure Vessels for Low Temperature Service 低溫壓力容器用碳鋼鋼板 |
|
|
|
CNS 12151
2017 Edition Electrical Insulating Compounds 電工用絕緣劑 |
|
|
|
CNS 13119
2017 Edition method of test for coefficient of static friction of paper and paperboard(Inclined plane method and horizontal plane method) 紙及紙板靜摩擦係數試驗法(傾斜平面法及水平平面法) |
|
|
|
CNS 1327
2017 Edition Testing method of Electrical Insulating Oils 電絕緣用油檢驗法 |
|
|
|
CNS 9476
2017 Edition Test Code for Accuracy of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床精度檢驗標準 |
|
|
|
CNS 1217
2017 Edition method of practice for manual sampling of petroleum and petroleum products 石油及其產品手動取樣法 |
|
|
|
CNS 15347
2017 Edition Safety of machinery − General principles for design − Risk assessment and risk reduction 機械安全－設計之一般原則－風險評鑑及風險降低 |
|
|
|
CNS 13804
2017 Edition Guidance on the Use of the Substitution method for Measurements of Radiation from Microwave Ovens for Frequencies above 1 GHz 應用置換法測量微波爐１ＧＨｚ以上之輻射指引 |
Translated |
|
|
CNS 12785
2017 Edition method of Test for Barcol Hardness of Glass Fiber Reinforced Plastics 玻璃纖維強化塑膠之巴可爾硬度測定法 |
|
|
|
CNS 10111
2017 Edition Preparation and Storage of Test Samples of Aluminium Fluoride for Industrial Use 天然及人造冰晶石試樣之製備與儲存 |
|
|
|
CNS 6834-6
2017 Edition Testing methods for rubber and plastics hoses - Part 6: Determination of adhesion between components 橡膠管及塑膠管試驗法－第6部：層間接著強度之測定 |
|
|
|
CNS 304
2017 Edition Hand Taps, metric (Two Pieces Per Set) 公制絲公，手用，每套兩件 |
Translated |
|
|
CNS 8785
2017 Edition method of Test for Electric Strength of Heat Shrinkable Tubing for Electrical Insulation 電絕緣用熱收縮套管絕緣強度試驗法 |
|
|
|
CNS 14607
2017 Edition Static electricity meters 電子式電度表 |
|
|
|
CNS 15564-4
2017 Edition ISO general purpose metric screw threads - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing ISO一般用途公制螺紋－公差－第4部：鍍鋅後依公差位置H或G攻牙之內螺紋相配合的熱浸鋅外螺紋之限界尺度 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [249] [250] [251] [252] [253] [254] [255] |
