"A, " CNS Standards List |
|
CNS 10766
2018 Edition Explosion-proof Bulkhead Lights for Marine Use 船用防爆艙壁燈 |
|
|
|
CNS 15710-2
2018 Edition Effects of current on human beings and livestock – Part 2: Special aspects 電流在人體及家畜上之效應－第2 部：特殊觀念 |
|
|
|
CNS 6866
2018 Edition Method of Test for Delivery Rate of Aerosol Products 噴霧性產品之噴出率檢驗法 |
Translated |
|
|
CNS 15652-2
2018 Edition Intelligent lighting systems – Part 2: Wide areA network interface 智慧照明系統－ 第2部：廣域網路介面 |
|
|
|
CNS 6714
2018 Edition Wood – Determination of water absorption 木材吸水性試驗法 |
|
|
|
CNS 9139
2018 Edition 660V Multi-Core EPR Insulated CP Sheathed Metal Netting Covered Cable (660V-MPNC) and 660V Multi-Core EPR Insulated CP Sheathed Metal Netting Covered PVC Anti-Corrosion Cable (660V-MPNCY) for Marine Use 船用６６０Ｖ多心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（６６０Ｖ–ＭＰＮＣ）及６６０Ｖ多心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（６６０Ｖ–ＭＰＮＣＹ） |
|
|
|
CNS 13789-4
2018 Edition Entity Authentication Mechanisms-Part 4:Mechanisms Using A Cryptographic Check Function 實體鑑別機制–第四部：使用密碼檢驗函數之機制 |
|
|
|
CNS 5749
2018 Edition Rectangular Copper Wires for Electrical Purposes 矩形銅線 |
|
|
|
CNS 3-13
2018 Edition Engineering Drawing (Geometrical Tolerancing - Positional Tolerancing) 工程製圖（幾何公差–位置度公差之標註） |
|
|
|
CNS 10686
2018 Edition Interface Between DatA Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange-Electrical Signal Characteristics 資料終端設備與資料電路終端設備間互換用串列二進資料之介面–信號特性 |
|
|
|
CNS 28000
2018 Edition Specification for security management systems for the supply chain 供應鏈安全管理系統規範 |
|
|
|
CNS 9603
2018 Edition Marine Halogen Lamp Type Flood Lights 船用汎光燈（鹵素電燈泡式） |
|
|
|
CNS 15676-1
2018 Edition Interior air of road vehicles − Part 1: Whole vehicle test chamber − Specification and method for the determination of volatile organic compounds in cabin interiors 道路車輛內部空氣－第1 部：整車試驗室－車廂內部揮發性有機化合物測定法 |
|
|
|
CNS 9391
2018 Edition Marine Fluorescent Table Lights 船用螢光枱燈 |
|
|
|
CNS 9330
2018 Edition Safety signs − General specification 安全標誌－一般性事項 |
|
|
|
CNS 3223
2018 Edition Power-Supply, Half-Wave, Metallic, Rectifier, Stack for Radio Receivers, Amplifiers, Etc. (110 Volts to 130 Volts, a.c.) 聚丙烯織製無縫邊袋（五十公斤裝砂糖用） |
|
|
|
CNS 14380-2
2018 Edition Banking - Key management (retail) - Part 2:Key management techniques for symmetric ciphers 銀行業－零售式金鑰管理－第2部：對稱密碼系統之金鑰管理技術 |
|
|
|
CNS 14484-6
2018 Edition Information technology - Keyboard layouts for text and office systems Part6: Function section 資訊技術-文件及辦公室系統用鍵盤配置-第６部：功能段 |
|
|
|
CNS 5525
2018 Edition Circuit Diagram (Schematic Diagram) for Sequential Control 順序控制接線展開圖 |
|
|
|
CNS 13798-2
2018 Edition Banking-Personal Identification Number Management and Security-Part 2:Approved Algorithm(s) for PIN Encipherment 銀行業–個人識別碼管理與安全（第二部：認可的個人識別碼加密演算法） |
|
|
|
CNS 15547-2
2018 Edition Mechanical vibration and shock – Evaluation of human exposure to whole-body vibration – Part 2: Vibration in buildings (1 Hz to 80 Hz) 機械振動與衝擊－人體曝露於全身振動的 評估－第2部：建築物內的振動(1Hz～80Hz) |
|
|
|
CNS 12993
2018 Edition Packaging - Complete, filled transport packages and unit loads - Vibration tests at fixed low frequency 包裝貨物與單位裝載之固定低頻率振動試驗法 |
|
|
|
CNS 62351-10
2018 Edition Power systems management and associated information exchange − DatA and communications security − Part 1: Communication network and system security − Introduction to security issues 電力系統管理及關聯資訊交換－資料及通訊安全－第10部：安全架構指導綱要 |
|
|
|
CNS 17190-4
2018 Edition Urine-absorbing aids for incontinence − Test methods for characterizing polymer-based absorbent materials − Part 4: Determination of moisture content by mass loss upon heating 尿失禁用尿液吸收輔具－聚合物吸收材料特性試驗法－第4部：以加熱質量損失法測定含水量 |
|
|
|
CNS 14364
2018 Edition Information technology - Open systems interconnection - Security frameworks for open systems: Security audit and alarms framework 資訊技術－開放系統互連－開放系統之安全框架：安全稽核及警報框架 |
|
|
|
CNS 4534
2018 Edition Terms of fasteners for screws,bolts,studs 結件詞彙（螺釘、螺栓、螺樁） |
|
|
|
CNS 5177
2018 Edition Method of test for wet tensile strength of paper and board 紙及紙板濕潤抗張強度試驗法 |
|
|
|
CNS 15703-3
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 3: Retention knobs for shanks of forms AC, AD, AF, UC, UD, UF, JD and JF 自動換刀器用7/24 錐度刀柄－第3 部：刀柄型式AC、AD、AF、UC、UD、UF、JD 及JF 之拉栓 |
|
|
|
CNS 11994
2018 Edition Cable Clamping Devices for Motor Starters and Controllers in Ships 船用電動機起動器及控制器之電纜固定方法 |
|
|
|
CNS 6512
2018 Edition Method of test for meat and meat products - Determination of chloride content 肉及肉製品檢驗法－氯化物含量之測定 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [242] [243] [244] [245] [246] [247] [248] |
