"T " CNS Standards List |
|
CNS 15091-24
2018 Edition MeThod of test for deep sea water - Determination of strontium 深層海水檢驗法－鍶之測定 |
|
|
|
CNS 8205
2018 Edition Deep groove ball bearings single-row wiThout filling notch, with ring groove 徑向深溝滾珠軸承－單列、無填裝槽、附扣環槽 |
|
|
|
CNS 13789-4
2018 Edition EnTity Authentication Mechanisms-Part 4:Mechanisms Using a Cryptographic Check Function 實體鑑別機制–第四部：使用密碼檢驗函數之機制 |
|
|
|
CNS 16070-1
2018 Edition Cycles − LighTing and retro-reflective devices − Part 1: Lighting and light signalling devices 自行車－照明及反光裝置－第1部：照明及燈光信號裝置 |
|
|
|
CNS 6866
2018 Edition MeThod of Test for Delivery Rate of Aerosol Products 噴霧性產品之噴出率檢驗法 |
Translated |
|
|
CNS 10602
2018 Edition Thyristor Rectifiers for Tloating Charge 浮接充電用閘流體整流器 |
|
|
|
CNS 10686
2018 Edition InTerface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange-Electrical Signal Characteristics 資料終端設備與資料電路終端設備間互換用串列二進資料之介面–信號特性 |
|
|
|
CNS 12268
2018 Edition Epoxy resin aluminium Tri-polyphosphate anticorrosive primer 環氧樹脂系三聚磷酸鋁防銹底漆 |
|
|
|
CNS 15704-1
2018 Edition 7/24 Taper spindle noses for automatic tool changers – Part 1: Dimensions and designation of spindle noses of forms S and SF 自動換刀器用7/24 錐度之主軸鼻端－第1 部：S 型及SF 型主軸鼻端之尺度及標示 |
|
|
|
CNS 2728
2018 Edition Aluminium STranded Wires for Insulated Cables 絕緣電纜用鋁絞線 |
Translated |
|
|
CNS 15676-1
2018 Edition InTerior air of road vehicles − Part 1: Whole vehicle test chamber − Specification and method for the determination of volatile organic compounds in cabin interiors 道路車輛內部空氣－第1 部：整車試驗室－車廂內部揮發性有機化合物測定法 |
|
|
|
CNS 2225
2018 Edition Low VolTage Fuses 低壓熔線 |
Translated |
|
|
CNS 13798-2
2018 Edition Banking-Personal IdenTification Number Management and Security-Part 2:Approved Algorithm(s) for PIN Encipherment 銀行業–個人識別碼管理與安全（第二部：認可的個人識別碼加密演算法） |
|
|
|
CNS 14199
2018 Edition Line Transmission of non-telephone signals - Codes for videoconferencing using primary digital group transmission 非電話信號之線傳輸–以原級數位群組傳輸之視訊會議編解碼器 |
|
|
|
CNS 13684
2018 Edition OpTical Interfaces for Equipments and Systems Relating the Synchronous Digital Hierarchy 同步數位階層設備與系統之光介面 |
|
|
|
CNS 9486
2018 Edition Marine Forged STeel Screw Escape Valves (30 kgf/㎠) 船用鍛鋼螺接型安全閥（30 kgf/㎠） |
|
|
|
CNS 9158
2018 Edition 250V Twin-Core,Three-Core EPR Insulated,CP Sheathed Metal Netting Covered Cable and 250V Twin-Core,Three-Core EPR Insulated Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用２５０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及２５０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 61347-2-3
2018 Edition Lamp conTrol gear − Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps 光源控制裝置－第2-3部：螢光燈管用交流/直流電子式控制裝置之個別要求 |
|
|
|
CNS 12238
2018 Edition Air cargo equipmenT − Base-restrained certified containers exclusively for the lower deck of large-capacity aircraft 空運貨櫃－廣體機下貨艙底盤受制認可貨櫃 |
|
|
|
CNS 17190-4
2018 Edition Urine-absorbing aids for inconTinence − Test methods for characterizing polymer-based absorbent materials − Part 4: Determination of moisture content by mass loss upon heating 尿失禁用尿液吸收輔具－聚合物吸收材料特性試驗法－第4部：以加熱質量損失法測定含水量 |
|
|
|
CNS 14153
2018 Edition Transmission of non-telephone signals - A real time control protocol for simplex applications using the H.221 LSD/HSD/MLP channels 非電話信號之傳輸–使用６４至１９２０ｋｂｐｓ通道訊框結構之ＬＳＤ／ＨＳＤ／ＭＬＰ通道之單工應用即時控制協定 |
|
|
|
CNS 16061
2018 Edition Burning behaviour of Textile and textile products − Vocabulary 紡織品及其產品之燃燒行為－詞彙 |
|
|
|
CNS 11994
2018 Edition Cable Clamping Devices for MoTor Starters and Controllers in Ships 船用電動機起動器及控制器之電纜固定方法 |
|
|
|
CNS 9812
2018 Edition MeThod of Test for Portable Electric Circular Saws 手提型電動圓鋸機試驗法 |
Translated |
|
|
CNS 14624-3
2018 Edition Infusion equipmenT for medical use-Part 3：Aluminum caps for infusion bottles 醫療用輸液設備─第三部份：點滴瓶鋁蓋 |
|
|
|
CNS 61347-2-9
2018 Edition Lamp conTrolgear − Part 2-9: Particular requirements for ballast of discharge lamps (excluding fluorescent lamps) 光源控制裝置－第2-9部：放電燈(螢光燈除外)用感抗式安定器之個別要求 |
|
|
|
CNS 13382-2
2018 Edition ImplanTs for surgery - Metallic materials - Wrought cobalt-chromium-tungsten-nickel alloy 外科體內植入物－金屬材料－鍛造鈷－鉻－鎢－鎳合金 |
|
|
|
CNS 2963
2018 Edition MeThod of Test for the Life of Electric Heating Wire and Ribbon 電熱線與電熱帶壽命試驗方法 |
|
|
|
CNS 4023
2018 Edition Permissible DeviaTion in Dimensions Without Tolerance Indication for Gas Cut Steel Plates 燄割鋼板之一般許可差 |
|
|
|
CNS 2379
2018 Edition Dried BoniTo and Mackerel 鰹鯖鰺類柴魚 |
|
| Find out:15111Items | To Page of: First -Previous-Next -Last | [237] [238] [239] [240] [241] [242] [243] |
