"A " CNS Standards List |
|
CNS 15620-2-1
2018 Edition InsulAtion coordination for equipment within low-voltage system – Part 2-1: Application Guide – Dimensioning procedure worksheets and dimensioning examples 低電壓系統下設備之絕緣協調－第2-1 部： 應用指引－ 尺寸量測程序工作表及尺寸量測範例 |
|
|
|
CNS 13789-4
2018 Edition Entity Authentication Mechanisms-Part 4:Mechanisms Using a Cryptographic Check Function 實體鑑別機制–第四部：使用密碼檢驗函數之機制 |
|
|
|
CNS 11794
2018 Edition Minimum Length Between the CAble Entrances and the Terminals of Electric Machinery and Equipment for Marine Use 船用電器電纜導入口與端子間之最小尺度 |
|
|
|
CNS 13382-1
2018 Edition ImplAnts for surgery - Metallic materials - Wrought stainless steel 外科體內植入物－金屬材料－鍛造不鏽鋼 |
|
|
|
CNS 15176-21
2018 Edition Wind turbines − PArt 21: Measurement and assessment of power quality characteristics of grid connected wind turbines 風力機－第21 部：併網型風力機之電力品質特性量測與評鑑 |
|
|
|
CNS 6950
2018 Edition Methed of test for residue Ash content of pulps, paper and board on ignition at 900℃ 紙漿、紙及紙板灰分試驗法－９００℃ |
|
|
|
CNS 15690
2018 Edition SterilizAtion of health care products − Vocabulary 健康照護產品滅菌－用語 |
|
|
|
CNS 3-5
2018 Edition Engineering DrAwing(Symbols for Riveting) 工程製圖（鉚接符號） |
|
|
|
CNS 13938-2
2018 Edition IdentificAtion cards - Contactless integrated circuit(s) cards; Part 2: Dimensions and location of coupling areas 識別卡–無接點ＩＣ卡；第２部：耦合區的尺寸與位置 |
|
|
|
CNS 10767
2018 Edition Explosion-proof PortAble Electric Lamps for Marine Use (Dry Cells and Batteries Type) 船用防爆手提燈（乾電池式） |
|
|
|
CNS 10234
2018 Edition 7/24 TAper for Spindle Noses and Tool Shanks 主心軸鼻端及刀柄用７／２４錐度 |
|
|
|
CNS 16057
2018 Edition PersonAl eye-protection − Automatic welding filters 個人眼睛防護－自動熔接濾光鏡片 |
|
|
|
CNS 9560
2018 Edition Round-steel link chAins for lifting - Grade 6 起重設備用圓鋼製環鏈－品質等級６ |
|
|
|
CNS 8884
2018 Edition PAllet racks 墊板式料架 |
|
|
|
CNS 14545-7
2018 Edition Fire hAzard testing-Part 2:Test methods-Section 1/sheet 3:Glow-wire ignitability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第３單元：材料引燃性之熾熱線試驗 |
|
|
|
CNS 15962-2
2018 Edition Control chArts − Part 2: Shewhart control charts 管制圖－第2部：修華特管制圖 |
|
|
|
CNS 174
2018 Edition SAddle Key and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉，用於鞍形鍵） |
|
|
|
CNS 10599
2018 Edition 600V GrAde ethylene - propylene rubber insulated cables 600V乙丙烯橡膠(EPR)絕緣電纜 |
Translated |
|
|
CNS 8965
2018 Edition MArine Bronze 16 kgf/㎠ Cocks 船用青銅旋塞（16 kgf/㎠） |
|
|
|
CNS 13661
2018 Edition ImplementAtion Requirement Profile of Associution Cortrol Services Element (ACSE), Presentation and Session Protocol for the use by FTAM 檔案轉送、存取及管理用結合控制服務元件、表現層及交談層等上層協定之實作需求規範 |
|
|
|
CNS 8268
2018 Edition GenerAl Requirements for Construction of Marine Electric Lighting Fittings Incandescent Lamps Type 船用白熾燈照明器具構造總則 |
|
|
|
CNS 15247
2018 Edition Test methods on light emitting diode components And modules (for general lighting service) for normal life 照明用發光二極體元件與模組之一般壽命試驗方法 |
Translated |
|
|
CNS 13932
2018 Edition TrAnsmission aspects of unbalance about earth (definitions and methods) 關於接地之不平衡的傳輸觀（定義及方法） |
|
|
|
CNS 4394-4
2018 Edition PlAstics − Injection moulding of test specimens of thermoplastic materials − Part 3: Small plates 塑膠－熱塑性塑膠射出成型試片－第4部：模製收縮率之測定 |
|
|
|
CNS 10035
2018 Edition Wooden Box for Export PAcking 木箱（外銷包裝用） |
|
|
|
CNS 15155
2018 Edition BiologicAl evaluation of medical devices - Part 19 : Physico-chemical, morphological and topographical characterization of materials 醫療器材生物性評估－第１９部：材料之物理化學、形態及拓撲學的特性分析 |
|
|
|
CNS 9965
2018 Edition Dimensions RelAting to Molds for Plastics Injection Molding Machines 塑膠射出成型機用金屬模具之相關尺度 |
|
|
|
CNS 14225
2018 Edition Lower lAyer protocol profiles for the Q3 interface 用於Ｑ３介面的低層協定規範 |
|
|
|
CNS 16050
2018 Edition Welding consumAbles − Gases and gas mixtures for fusion welding and allied processes 銲接材料－熔融銲接及相關程序用氣體及混合氣 |
|
|
|
CNS 14989
2018 Edition MedicAl devices - Application of risk management to medical devices 醫療器材風險管理 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [237] [238] [239] [240] [241] [242] [243] |
