"an " CNS Standards List| Method Test | Method Test | Terms relating | Furniture | Method test | Essential oils | Method Test | Footwear − | |
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 5026
1984 Edition Welding Transformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 6409
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 6408
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Zone Factor Zн 圓柱齒輪與傘齒輪之負載能力計算－齒廓面作用帶因數Ｚ H |
|
|
|
CNS 6412
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Helix Angle Factor Yᵦ 圓柱齒輪與傘齒輪之負載能力計算－螺旋角因數Ｙβ |
|
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical and Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 6414
1984 Edition Basic Rack of Straight Bevel Gears for General and Heavy Engineering 直齒傘齒輪之基準齒條(一般機械及重機械用) |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5280
1984 Edition Helix angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 177
1983 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 10118
1983 Edition Method for Determining Calcium Content in Natural and Artificial Cryolite (Flame Atomic Absorption Method) 天然及人造冰晶石中鈣定量法（火焰原子吸光法） |
|
|
|
CNS 10120
1983 Edition Method for Determining Water Content in Natural and Artificial Cryolite and Aluminium Fluoride for Industrial Use (Electrometric Method) 天然及人造冰晶石與工業用氟化鋁中水定量法（電計滴定法） |
|
|
|
CNS 10114
1983 Edition Method for Determining Iron Content in Natural and Artificial Cryolite (1,10-Phenanthroline Photometric Method) 天然及人造冰晶石中鐵定量法（二氮雜菲吸光光度法） |
|
|
|
CNS 10121
1983 Edition Method for Determining Moisture Content in Natural and Artificial Cryolite and Aluminium Flouride for Industrial Use (Gravimetric Method) 天然及人造冰晶石與工業用氟化鋁中水分定量法（重量法） |
|
|
|
CNS 10115
1983 Edition Method for Determining Sodium Content in Natural and Artificial Cryolite (Flame Emission and Atomic Absorption Spectrophotometric Methods) 天然及人造冰晶石中鈉定量法（火焰光度法及原子吸光法） |
|
|
|
CNS 10116
1983 Edition Method for Determining Aluminium Content in Natural and Artificial Cryolte {Oxine (8-Hydroxyquinoline) Gravimetric Method} 天然及人造冰晶石中鋁定量法〔喔星(8－羥基喹啉)重量法〕 |
|
|
|
CNS 10113
1983 Edition Method for Determining Fluorine Content in Natural and Artificial Cryolite (Modified Willard Winter Method) 天然及人造冰晶石中氟定量法（改良威拉－溫特法） |
|
|
|
CNS 8214
1983 Edition Testing Method of Outside and Inside Diameters Wrapped Bushes for Plain Bearing 滑動軸承用捲製軸承襯檢驗法(外徑及內徑) |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys and Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [232] [233] [234] [235] [236] [237] [238] |
