"An " CNS Standards List |
|
CNS 5277
1984 Edition Cylindrical Gear for Fine MechAnics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 5275
1984 Edition Base TAngent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5274
1984 Edition Base TAngent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth TolerAnce for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth TolerAnce for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 6409
1984 Edition Calculation of Load Capacity for Cylindrical And Bevel Gears-Material Factor Zм 圓柱齒輪與傘齒輪之負載能力計算－材料因數ＺM |
|
|
|
CNS 11093
1984 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated And Sheated Cables: VVF) 屋內配線用接線盒[平型聚氯乙烯絕緣聚氯乙烯被覆電纜(VVF)] |
|
|
|
CNS 11160
1984 Edition Octave And Third-octave Band Analyzers for Sounds and Vibrations 聲音及振動用八音度及1/3八音度頻帶分析器 |
|
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine MechAnics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre DistAnces and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 5027
1984 Edition Control Timers for ResistAnce Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 6411
1984 Edition Calculation of Load Capacity for Cylindrical And Bevel Gears-Contact Ratio Factor Zε 圓柱齒輪與傘齒輪之負載能力計算－接觸比因數Ｚε |
|
|
|
CNS 9705
1984 Edition General Rules for Emission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum SAnders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 11071
1984 Edition Emission-Spectroscopic Analysis for Carbon Steel and Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
|
|
|
CNS 6407
1984 Edition Calculation of Load Capacity for Cylindrical And Bevel Gears-Load Sharing Factor Ｙε and Overlap Ratio εβ 圓柱齒輪與傘齒輪之負載能力計算－負載分配因數Ｙε及齒進度比εβ |
|
|
|
CNS 11072
1984 Edition Method of X-Ray Fluorescence Spectrometric Analysis of Iron and Steel 鐵及鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 6410
1984 Edition Calculation of Load Capacity for Cylindrical And Bevel Gears-Pinion Single Tooth Contact Factor Zв, Wheel Single Tooth Contact Factor Zᴅ and Transverse Contact Ratio ε⍺ 圓柱齒輪與傘齒輪之負載能力計算－小齒輪單齒接觸因數ＺB，大齒輪單齒接觸因數ＺD及正面接觸比εα |
|
|
|
CNS 5026
1984 Edition Welding TrAnsformers for Portable Spot Welding Machine 手提型點焊機用變壓器 |
|
|
|
CNS 11014
1984 Edition Methods of Determination for MAnganese in Iron and Steel 鋼鐵中錳定量法 |
|
|
|
CNS 167
1983 Edition Double TAngential Keys 雙切線鍵 |
|
|
|
CNS 6094
1983 Edition EntrAnce Caps for Rigid Steel Conduit 電線用鋼管進口蓋 |
|
|
|
CNS 6876
1983 Edition Spindle Noses And Face Plates of Lathes 車床之主心軸鼻端及面板 |
|
|
|
CNS 169
1983 Edition Flat Fitting Keys And Sliding Cotter 配合平鍵及滑鍵 |
|
|
|
CNS 10121
1983 Edition Method for Determining Moisture Content in Natural And Artificial Cryolite and Aluminium Flouride for Industrial Use (Gravimetric Method) 天然及人造冰晶石與工業用氟化鋁中水分定量法（重量法） |
|
|
|
CNS 10111
1983 Edition Preparation And Stroage of Test Samples of Natural and Artificial Cryolite 天然及人造冰晶石試樣之製備與儲存 |
|
|
|
CNS 178
1983 Edition Flat Fitted Keys And Its Seat (for Taper Shaft End) 配合平鍵及槽（用於錐軸梢） |
|
|
|
CNS 168
1983 Edition TAngential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 171
1983 Edition Screw And Hole for Sliding Key 滑鍵螺釘及孔 |
|
|
|
CNS 173
1983 Edition Key Section And Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [232] [233] [234] [235] [236] [237] [238] |
