"1 " CNS Standards List |
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 4551
2017 Edition Gas Cylinders; Thread for Nozzles, Neck Rings and Protection Caps 瓦斯瓶用螺紋 |
|
|
|
CNS 14820
2017 Edition Method of test for measuring toxic gases generated by solid material flammability － Gas detector tube 固體材料燃燒毒性氣體濃度試驗法－檢測管法 |
|
|
|
CNS 4555
2017 Edition Hexagon Socket Head Cap Screws M 1.4 to M 2.5 六角承窩頭螺釘（M1.4至M2.5） |
Translated |
|
|
CNS 3618
2017 Edition Single-Phase Induction Motors(under 100 Watt) １００瓦以下單相感應電動機 |
Translated |
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 13330
2017 Edition Dynamo Lamp for Bicycles 自行車（腳踏車）用發電燈 |
|
|
|
CNS 14471
2017 Edition Method of test for sulfur in petroleum products − High temperature combustion and IR detection 石油產品硫含量試驗法－高溫燃燒與紅外線檢測 |
|
|
|
CNS 13001
2017 Edition Method of Radiographic Testing for Circumferential Butt Welds of Aluminum Pipes and Tubes 鋁管圓周對頭熔接縫之放射線透射試驗法 |
|
|
|
CNS 1130
2017 Edition Pliers and nippers - Engineer's and lineman's pliers 夾鉗與剪鉗－一般技術要求 |
|
|
|
CNS 13546-2
2017 Edition Plastics − Poly (methyl methacrylate) (PMMA) moulding and extrusion materials − Part 1: Designation system and basis for specifications 塑膠－聚甲基丙烯酸甲酯(PMMA)模製及押出材料－第2部：試片製備及性質測定法 |
|
|
|
CNS 218
2017 Edition Counter-boring Drill with Morse Taper Shank （莫氏）推拔柄柱坑鑽頭 |
Translated |
|
|
CNS 11828
2017 Edition Method of Test for Blast Furnace Slag for Road Construction 道路用高爐爐碴檢驗法 |
Translated |
|
|
CNS 12867
2017 Edition Basic Environmental Testing Procedures Part 2 : Tests-Test Z/AM : Combined Dry Heat/Low Air Pressure Tests 環境試驗法（電氣、電子）–高溫／低氣壓複合試驗法 |
|
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 12240
2017 Edition Construction of Layered Pressure Vessels 多層卷壓力容器 |
|
|
|
CNS 13075
2017 Edition Non-invasive automated sphygmomanometers 非侵入式自動血壓計 |
|
|
|
CNS 12846
2017 Edition Helium Mass Spectrometer Leak Testing by Trace Probe Method 氦質譜儀示蹤氣探針探漏法 |
|
|
|
CNS 13517
2017 Edition Large diameter welded stainless steel pipes 配管用銲接大口徑不銹鋼鋼管 |
|
|
|
CNS 131
2017 Edition Tail Spindle (Using Morse Taper 0-6, Metric Taper 4, 6, 80-200, Without Flat End) 頂針（用莫氏圓錐０–６公制圓錐４，６，８０–１２０） |
|
|
|
CNS 12338
2017 Edition Crowbars 撬桿 |
|
|
|
CNS 13059-3
2017 Edition Photovoltaic Devices Part 3：Measurement Principles for Terrestrial Photovoltaic (PV) Solar Devices with Reference Spectral Irradiance Data 光電伏打元件（第三部：具光譜照射光參考數據之陸上光電伏打（ＰＶ）太陽元件量測原理） |
|
|
|
CNS 16015-1
2017 Edition Transportation of dangerous goods − Part 1: Requirement for the construction and testing of packagings 危險貨物之運輸－第1部：包裝物之構造與試驗要求 |
|
|
|
CNS 10723
2017 Edition Guide for characterizing hydrocarbon lubricant base oils 烴類潤滑基礎油鑑別指引 |
|
|
|
CNS 168
2017 Edition Tangential Key for Impact Type Reversal Load 切線鍵（用於衝擊式之變向負荷） |
|
|
|
CNS 15551-2
2017 Edition Ergonomics - Accessible design - Sound pressure levels of auditory signals for consumer products 人因工程－無障礙設計 - 消費 產品中聲音訊號之聲壓位準 |
|
|
|
CNS 11570
2017 Edition Remote Control Relays and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 14557
2017 Edition Method of reliability test for road traffic LED display panel 道路用發光二極體文字顯示型交通資訊看板之可靠度測試 |
|
|
|
CNS 173
2017 Edition Key Section and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉） |
|
| Find out:10860Items | To Page of: First -Previous-Next -Last | [229] [230] [231] [232] [233] [234] [235] |
