"P " CNS Standards List |
|
CNS 14623-2
2017 Edition Sterilization of health care Products-chemical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 162
2017 Edition Testing Standard for SPring Washer 彈簧墊圈檢驗標準 |
Translated |
|
|
CNS 6878
2017 Edition Machine Nut TaPs, for Coarse ISO Metric Threads 螺帽攻（ＩＳＯ公制粗螺紋） |
|
|
|
CNS 15091-1
2017 Edition Method of test for deeP sea water - Measurement of in-situ temperature 深層海水檢驗法－現場溫度之測量 |
|
|
|
CNS 8919
2017 Edition Auxiliaries of Stationary Centrifugal Fire Pumps 固定式消防用加壓離心泵之附屬裝置 |
|
|
|
CNS 4701
2017 Edition Hexagon Domed CaP Bolts 六角蓋頭螺栓 |
|
|
|
CNS 15528
2017 Edition Plastic Cup ( replaced by CNS 2446 ) 塑膠吸管 |
|
|
|
CNS 12361
2017 Edition Method of Test for Fiber OPtic Devices ( FOTP-85 Fiber Optic Cable Twist Test) 光纖裝置檢驗法（光纜扭轉試驗ＦＯＴＰ–８５） |
|
|
|
CNS 8474
2017 Edition Punched Tape Variable Block Format for Positioning and Straight - Cut Numerically Controlled Machine Tools 衝頭（對孔用） |
|
|
|
CNS 12884
2017 Edition Method of samPling and preparing wood for general analysis and preparation of wood for chemical analysis 紙漿用木材取樣與調製法及化學分析用木材之製備法 |
|
|
|
CNS 853
2017 Edition Cross Joints With Quadri - Flange (Working Pressure Less Than 16 kgf/c㎡) 凸緣十字管接頭（使用壓力16 kgf/㎠） |
|
|
|
CNS 5989
2017 Edition Pumps – Testing – Submersible mixers for wastewater and similar applications 衝模用上模座及下模座 |
|
|
|
CNS 1016
2017 Edition Picks, One Conical End and One Flat End 十字鎬（一端為斜錐狀，一端為扁平狀） |
|
|
|
CNS 2692
2017 Edition Pliers and nippers - Pliers for gripping and manipulating 夾鉗與剪鉗－滑節轉樞夾鉗（鯉魚鉗） |
|
|
|
CNS 12664
2017 Edition Method of Test for Qualification Procedure of Welding Technique of Plastics 鑑定熔接塑膠技術之試驗法 |
|
|
|
CNS 13067
2017 Edition Methods of Test for EPoxy Equivalent of Epoxy Resins 環氧樹脂之環氧當量試驗法 |
|
|
|
CNS 3098
2017 Edition Nail Pullers 拔釘鈎 |
|
|
|
CNS 4551
2017 Edition Gas Cylinders; Thread for Nozzles, Neck Rings and Protection Caps 瓦斯瓶用螺紋 |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed Carbon ComPosition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 16016-5
2017 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 3: Fittings 冷熱水裝置用塑膠管配管系統－聚丙烯(PP)－第5部：系統適合度 |
|
|
|
CNS 4555
2017 Edition Hexagon Socket Head CaP Screws M 1.4 to M 2.5 六角承窩頭螺釘（M1.4至M2.5） |
Translated |
|
|
CNS 13805
2017 Edition Method of Measurement for Photoluminescence of Optoelectronic Semiconductor Wafers 光電半導體晶圓之光激光譜量測法 |
|
|
|
CNS 15968
2017 Edition Plastics − Film and sheeting − Measurement of water-contact angle of corona-treated films 塑膠－薄膜及薄片－電暈處理薄膜水接觸角量測法 |
|
|
|
CNS 4367
2017 Edition Knuckle Threads for Steel Sheet Pieces (up to 0.5 mm Thickness and Appropriated Couplings Dimensions Tolerances) 圓螺紋（厚0.5mm以下之鋼皮製品及其 配合螺紋） |
|
|
|
CNS 13075
2017 Edition Non-invasive automated sPhygmomanometers 非侵入式自動血壓計 |
|
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical Connectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 14471
2017 Edition Method of test for sulfur in Petroleum products − High temperature combustion and IR detection 石油產品硫含量試驗法－高溫燃燒與紅外線檢測 |
|
|
|
CNS 13330
2017 Edition Dynamo LamP for Bicycles 自行車（腳踏車）用發電燈 |
|
|
|
CNS 12867
2017 Edition Basic Environmental Testing Procedures Part 2 : Tests-Test Z/AM : Combined Dry Heat/Low Air Pressure Tests 環境試驗法（電氣、電子）–高溫／低氣壓複合試驗法 |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [228] [229] [230] [231] [232] [233] [234] |
