"An " CNS Standards List |
|
CNS 4320
1987 Edition Hexagon Head Bolts, Finished And Semi-Finished, Metric Fine Thread 六角頭螺栓（精製及半精制，公制細螺紋） |
|
|
|
CNS 4321
1987 Edition Hexagon Bolts with Approximately to Head, Finished And Semi-Finished, Metric Fine Thread 六角頭全螺紋螺栓（精製及半精製，公制細螺紋） |
|
|
|
CNS 9234
1987 Edition Method of Test for Dry Reed Switches (StAndard Test Coils, Single Insulation 130 ℃ Wire) 乾式簧開關檢驗法（130℃單層絕緣線標準試驗線圈） |
|
|
|
CNS 9229
1987 Edition Method of Test for Dry Reed Switches (Lead Finish And Terminal Strength) 乾式簧開關檢驗法（引線表面處理與端子強度） |
|
|
|
CNS 9228
1987 Edition Method of Test for Dry Reed Switches (CapacitAnce) 乾式簧開關檢驗法（電容量） |
|
|
|
CNS 9114
1987 Edition Symbols of Television And Broadcast Equipment of Interior Wiring Diagram for Architectural Plans 屋內配線設計圖電視、播音類符號 |
|
|
|
CNS 12128
1987 Edition General Rules for Methods of Potentiometric, Amperometric, And Coulometric Titrations 電位差、電流、電量滴定法通則 |
|
|
|
CNS 11999
1987 Edition Structural Steels with Specified Hardenability BAnds 保證硬化能構造用鋼料（Ｈ鋼） |
|
|
|
CNS 11892
1987 Edition Shears for Flower And Grass Cutting 手剪（修剪花草用） |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks And Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 5745
1987 Edition Method of test for Electrical Copper And Aluminium Wires 銅電線及鋁電線檢驗法 |
|
|
|
CNS 5987
1987 Edition ShAnks of Press Die 衝模柄 |
|
|
|
CNS 11940
1987 Edition StAndard Parts of Injection Mold 塑膠型模形狀及其標準組件 |
|
|
|
CNS 12085
1987 Edition Method of Test for Fiber Optic Devices (FOTP-54 Mode Scrambler Launch Requirements for Information TrAnsmission Capacity Measurements) 光纖裝置檢驗法（資訊傳輸量測量之模攪拌器投射需求FOTP-54） |
|
|
|
CNS 4776
1987 Edition Electric RadiAnt Heater 反射電暖爐 |
Translated |
|
|
CNS 12007
1987 Edition Method of Test for Helical ScAnning Video Tape Recorders 螺線掃描錄放影機檢驗法 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 6032
1987 Edition Alkaline Primary Cells And Batteries 鹼性一次電池 |
|
|
|
CNS 12076
1987 Edition Die Wear TolerAnce for Hot Forging Closed Die 熱鍛閉合模之模具磨耗許可量 |
|
|
|
CNS 12077
1987 Edition Minimum Rounded Radii And Drafts of Hot Forging Closed Die 熱鍛閉合模之最小圓角半徑與拔模斜度(角度) |
|
|
|
CNS 12081
1987 Edition Method of Test for Fiber Optic Devices (FOPT-13 Visual And Mechanical Inspection of Fibers,Cables,Connectors and Other Fiber Optic Devices) 光纖裝置檢驗法（光纖、光纜、連接器及其他光纖裝置之目視及機械檢查FOTP-13） |
|
|
|
CNS 12082
1987 Edition Method of Test for Fiber Optic Devices (FOPT-30 Frequency Domain Measurement of Multimode Optical Fiber Information TrAnsmission Capacity) 光纖裝置檢驗法（多模光纖資訊傳輸量之頻域測量FOTP-30） |
|
|
|
CNS 12083
1987 Edition Method of Test for Fiber Optic Devices (FOPT-33 Fiber Optic Cable Tensile Loading And Bending Test) 光纖裝置檢驗法（光纜拉力負載與彎曲試驗FOTP-33） |
|
|
|
CNS 5988
1987 Edition Stud ShAnks for Press Dies 衝模用栓柄 |
|
|
|
CNS 7962
1986 Edition Test Code for PerformAnce of Numerically Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 7660
1986 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 21 Insulation ResistAnce) 頻率3 MHz以下電連接器檢驗法（絕緣電阻T-21） |
|
|
|
CNS 7659
1986 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 20 with StAnding Voltage Test) 頻率3 MHz以下電連接器檢驗法（耐壓檢驗TP-20） |
|
|
|
CNS 5663
1986 Edition Test Code for Accuracy of Three-Side PlAners and Moulders 自動三面刨床精度檢驗標準 |
|
|
|
CNS 5664
1986 Edition Test Code for Accuracy of Four-side PlAners and Moulders 自動四面刨床精度檢驗標準 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [228] [229] [230] [231] [232] [233] [234] |
