"P " CNS Standards List |
|
CNS 9369
2017 Edition Method of Test for Low Frequency (Below 3 MHz) Electrical Connectors (TP - 35 Proposed Insert Retention) 頻率３ＭＨｚ以下電連接器檢驗法（接觸端子插入扣鎖ＴＰ–３５） |
|
|
|
CNS 4556
2017 Edition Hexagon Socket Head CaP Screws with Reduced Height of Head 六角承窩短頭螺釘 |
Translated |
|
|
CNS 6860
2017 Edition ResPiratory protective devices − Self-contained open-circuit compressed air breathing apparatus with full face mask − Requirements, testing, marking 呼吸防護裝置－全面罩壓縮空氣開放式自攜呼吸器－要求、試驗、標示 |
|
|
|
CNS 309
2017 Edition TaPs for Metric Threading Dies 絲公，適於公制螺絲鋼板 |
Translated |
|
|
CNS 10940
2017 Edition Precision Surface Plates 著色塗覆鍍鋅低碳鋼線 |
|
|
|
CNS 6701
2017 Edition Safety Belts (Fasten TyPe) 安全帶（繫身型） |
Translated |
|
|
CNS 15562-7
2017 Edition Stationary training equiPment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備－第7部：划船機－附加之特定安全要求與試驗法 |
|
|
|
CNS 14555
2017 Edition Road traffic LED disPlay panel 道路用發光二極體文字顯示型交通資訊看板 |
|
|
|
CNS 8698
2017 Edition Nickel Steel Plates for Pressure Vessels for Low Temperature Service 低溫壓力容器用鎳鋼鋼板 |
|
|
|
CNS 1014
2017 Edition Picks (Single), One Taper End Only 十字鎬（各部份名稱） |
|
|
|
CNS 14466-8
2017 Edition Audiovisual,video and television equiPment and systems. Part8:Syinbols and identification 視聽．影像及電視設備與系統-第８部：符號標誌與識別 |
|
|
|
CNS 12210
2017 Edition Method of Test for Sets of High Strength Torque Control Bolt, Hexagon Nut and Plain Washers 控制扭矩之高強度螺栓、六角螺帽及平墊圈組檢驗法 |
|
|
|
CNS 15969
2017 Edition Structural requirements of railway vehicle bodies of the locomotives and Passenger rolling stock 機車及客車軌道車輛車體結構要求 |
|
|
|
CNS 13065
2017 Edition Methods of Test for Viscosity of EPoxy Resins and Hardeners 環氧樹脂及硬化劑黏度測定法 |
|
|
|
CNS 8918
2017 Edition Primary Standards ( replaced by CNS 12983 ) 固定式消防用加壓離心泵之原動機 |
|
|
|
CNS 5770
2017 Edition General SPecification for Thermistors, Insulated and Non-Insulated 絕緣及無絕緣熱敏電阻器通則 |
|
|
|
CNS 12854
2017 Edition Fire Fighting EquiPment for Liquefied Petroleum Gas Plant Use 液化石油氣設施用消防設備 |
|
|
|
CNS 6834-8
2017 Edition Testing methods for rubber and Plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 12865-1
2017 Edition Method of Test for Digital Microelectronics ( High Level OutPut Voltage ) 數位微電子檢驗法（高位準輸出電壓） |
|
|
|
CNS 503
2017 Edition ISO Metric Fine Screw Threads (Diameters from 18 to 150mm and Pitch 2mm) 公制細螺紋6（ISO制）（標稱直徑18至150公釐，螺距2公釐） |
|
|
|
CNS 5961
2017 Edition General Rules for InsPection of Valves 閥之檢驗總則 |
|
|
|
CNS 513
2017 Edition Metric TraPezoidal Screw Threads Allowance and Tolerances for General Purpose Trapezoidal Screw Threads 梯形螺紋（一般用梯形螺紋的裕度及公差） |
|
|
|
CNS 16022
2017 Edition Acoustics − Determination of dynamic stiffness − Part 1: Materials used under floating floors in dwellings 聲學－動態剛性測定法－用於住宅浮式地板下之材料 |
|
|
|
CNS 13194
2017 Edition Test Methods for Performance and Accuracy of Double Sizers 雙端截鋸機之性能試驗及精度檢驗法 |
|
|
|
CNS 15207-10
2017 Edition Road vehicles - ComPonent test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 10: Immunity to conducted disturbances in the extended audio frequency range 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第10部：音頻延伸範圍之傳導擾動免疫力 |
|
|
|
CNS 11329
2017 Edition Test Method for the Sets of High Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
|
|
|
CNS 3094
2017 Edition Solid Punches 衝頭 |
|
|
|
CNS 283
2017 Edition Methods of samPling and chemical analysis of common salt 工業鹽取樣法及化學分析法 |
|
|
|
CNS 1358
2017 Edition Method of Test for Folding Endurance of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
Translated |
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems Using the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
| Find out:11004Items | To Page of: First -Previous-Next -Last | [215] [216] [217] [218] [219] [220] [221] |
