"D C " CNS Standards List |
|
CNS 6512
2018 Edition Method of test for meat and meat products - Determination of chloride content 肉及肉製品檢驗法－氯化物含量之測定 |
|
|
|
CNS 1987
2018 Edition Sodium sulfate 硫酸鈉 |
|
|
|
CNS 363-2
2018 Edition Bicycle tyres and rims − Part 2: Rims 自行車輪胎與輪圈－第2部：輪圈 |
|
|
|
CNS 1133
2018 Edition Pliers and nippers - Construction worker`s pincers 夾鉗與剪鉗－對口斜角剪鉗（斜口鉗） |
|
|
|
CNS 12431
2018 Edition Fittings for sliding windows 橫拉窗用五金 |
|
|
|
CNS 13789-5
2018 Edition Information technology ─ Security technigues ─ Entity authentication ─Part 5: Mechanisms using zero knowledge techniques 資訊技術─安全技術─實體鑑別機制—第5部：使用零資訊技術機制 |
|
|
|
CNS 15091-24
2018 Edition Method of test for deep sea water - Determination of strontium 深層海水檢驗法－鍶之測定 |
|
|
|
CNS 9636
2018 Edition Chilled Fish 冷藏魚類 |
|
|
|
CNS 9139
2018 Edition 660V Multi-Core EPR InsulateD CP Sheathed Metal Netting Covered Cable (660V-MPNC) and 660V Multi-Core EPR Insulated CP Sheathed Metal Netting Covered PVC Anti-Corrosion Cable (660V-MPNCY) for Marine Use 船用６６０Ｖ多心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（６６０Ｖ–ＭＰＮＣ）及６６０Ｖ多心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（６６０Ｖ–ＭＰＮＣＹ） |
|
|
|
CNS 14961
2018 Edition Small medical gas cylinders - Pin-index yoke-type valve connections 小型醫療氣體鋼瓶－銷針標示軛式閥接頭 |
|
|
|
CNS 15704-1
2018 Edition 7/24 taper spindle noses for automatic tool changers – Part 1: Dimensions and designation of spindle noses of forms S and SF 自動換刀器用7/24 錐度之主軸鼻端－第1 部：S 型及SF 型主軸鼻端之尺度及標示 |
|
|
|
CNS 6866
2018 Edition Method of Test for Delivery Rate of Aerosol Products 噴霧性產品之噴出率檢驗法 |
Translated |
|
|
CNS 14199
2018 Edition Line transmission of non-telephone signals - Codes for videoconferencing using primary digital group transmission 非電話信號之線傳輸–以原級數位群組傳輸之視訊會議編解碼器 |
|
|
|
CNS 10802
2018 Edition Single-Start and Double-Start Trapezoidal Screw Thread with Clearance for Railway Rolling Stock (Theoretical Values) 鐵路車輛用單頭與雙頭梯形螺紋（理論值） |
|
|
|
CNS 15436
2018 Edition Self-ballasted LED-lamps for general lighting services – Safety specifications 安定器內藏式發光二極體燈泡(一般照明用)－安全性要求 |
|
|
|
CNS 13684
2018 Edition Optical Interfaces for Equipments and Systems Relating the Synchronous Digital Hierarchy 同步數位階層設備與系統之光介面 |
|
|
|
CNS 4023
2018 Edition Permissible Deviation in Dimensions Without Tolerance Indication for Gas Cut Steel Plates 燄割鋼板之一般許可差 |
|
|
|
CNS 11994
2018 Edition Cable Clamping Devices for Motor Starters anD Controllers in Ships 船用電動機起動器及控制器之電纜固定方法 |
|
|
|
CNS 8187
2018 Edition Method of Test for Building Components (Steel Panel for Floor) 建築用組件（鋼製樓板嵌板）檢驗法 |
|
|
|
CNS 13661
2018 Edition Implementation Requirement Profile of Associution Cortrol Services Element (ACSE), Presentation and Session Protocol for the use by FTAM 檔案轉送、存取及管理用結合控制服務元件、表現層及交談層等上層協定之實作需求規範 |
|
|
|
CNS 5525
2018 Edition Circuit Diagram (Schematic Diagram) for Sequential Control 順序控制接線展開圖 |
|
|
|
CNS 5064
2018 Edition Methods of Luminance Measurements 輝度測量法 |
|
|
|
CNS 61347-2-9
2018 Edition Lamp controlgear − Part 2-9: Particular requirements for ballast of discharge lamps (excluding fluorescent lamps) 光源控制裝置－第2-9部：放電燈(螢光燈除外)用感抗式安定器之個別要求 |
|
|
|
CNS 10037
2018 Edition Method of Test for Particle-Size Distribution of Space-Insecticide Aerosol 空間殺蟲劑噴霧粒子大小分布之試驗法 |
|
|
|
CNS 2956
2018 Edition Method of test for ring crush of corrugating medium paper and board 瓦楞芯紙及紙板環壓強度試驗法 |
|
|
|
CNS 15676-1
2018 Edition Interior air of road vehicles − Part 1: Whole vehicle test chamber − Specification and method for the determination of volatile organic compounds in cabin interiors 道路車輛內部空氣－第1 部：整車試驗室－車廂內部揮發性有機化合物測定法 |
|
|
|
CNS 15169
2018 Edition Method of test for the concentration of polynuclear aromatic hydrocarbons (PAHs) as burning of joss sticks 香品燃燒所產生之多環芳香烴化合物測定法 |
|
|
|
CNS 17190-4
2018 Edition Urine-absorbing aids for incontinence − Test methods for characterizing polymer-based absorbent materials − Part 4: Determination of moisture content by mass loss upon heating 尿失禁用尿液吸收輔具－聚合物吸收材料特性試驗法－第4部：以加熱質量損失法測定含水量 |
|
|
|
CNS 15703-1
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 1: Dimensions and designation of shanks of forms A, AD, AF, U, UD and UF 自動換刀器用7/24 錐度刀柄－第1 部：刀柄型式A、AD、AF、U、UD 及UF 之尺度及標示 |
|
|
|
CNS 61347-2-3
2018 Edition Lamp control gear − Part 2-3: Particular requirements for a.c. and/or d.c. supplied electronic control gear for fluorescent lamps 光源控制裝置－第2-3部：螢光燈管用交流/直流電子式控制裝置之個別要求 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [209] [210] [211] [212] [213] [214] [215] |
