"5 " CNS Standards List| Machine tools | Method test | Draw | Skimmilk, Dried | Modified Polyester | Method Test | Method Test | Methods measurement | |
|
CNS 5989
1985 Edition Punch Holder and Die Holder for Press Dies 衝模用上模座及下模座 |
|
|
|
CNS 5962
1985 Edition Bronze Screwed Globe Valves (5kgf/c㎡) 青銅螺紋口球形閥(5 kgf/cm2) |
|
|
|
CNS 5968
1985 Edition Bronze Screwed Lift Check Valves (10kgf/c㎡) 青銅螺紋口升降型止回閥(10 kgf/cm2) |
|
|
|
CNS 5969
1985 Edition Bronze Flanged Globe Valves (10kgf/c㎡) 青銅凸緣型球形閥(10 kgf/cm2) |
|
|
|
CNS 6552
1985 Edition Test Code for Performance of Table Type Horizontal Boring Machines 床台型臥式搪床動態檢驗法 |
|
|
|
CNS 5970
1985 Edition Bronze Flanged Angle Valves (10kgf/c㎡) 青銅凸緣型角閥(10 kgf/cm2) |
|
|
|
CNS 5971
1985 Edition Bronze Flanged Gate Valves (10kgf/c㎡) 青銅凸緣型閘閥(10 kgf/cm2) |
|
|
|
CNS 5267
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Cumulative Circular Pitch 圓柱齒輪輪齒之精度（累積周節誤差之公差） |
|
|
|
CNS 3150
1984 Edition Crowbars 撬桿 |
|
|
|
CNS 5283
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Tooth Trace 圓柱齒輪輪齒之精度(齒廓面元線誤差之公差) |
|
|
|
CNS 5284
1984 Edition Addendum Modification of Spur Gears in the 0.5 System, Introduction 0.5齒制正齒輪之齒廓移位 |
|
|
|
CNS 5285
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Indevidual Parameters 圓柱齒輪輪齒之精度（個別參數誤差之公差） |
|
|
|
CNS 5027
1984 Edition Control Timers for Resistance Welding Machine of Lap Joint 搭接電阻電焊機用時間控制器 |
|
|
|
CNS 5030
1984 Edition Projection Welding Machine 凸壓電焊機 |
|
|
|
CNS 5028
1984 Edition Rectifier Type DC Arc Welding Machines with Drooping Characteristic 穩流整流式直流電弧電焊機 |
|
|
|
CNS 5282
1984 Edition Basic Rack of Gear-Cutting Tools for Involute Tooth System 漸開線齒制用切齒刀具之基準齒條 |
|
|
|
CNS 5280
1984 Edition Helix Angles for Cylindrical Gears 圓柱齒輪之螺旋角 |
|
|
|
CNS 5277
1984 Edition Cylindrical Gear for Fine Mechanics (Radial Setting of Tool) 精細機械用圓柱齒輪（齒跨距測量工具之徑向調整量數值表） |
|
|
|
CNS 2305
1984 Edition Asphalt Laminating Paper 夾層柏油紙 |
Translated |
|
|
CNS 5276
1984 Edition Factor COSα/COSαw of Spur Gears for Fine Mechanics 精細機械用正齒輪（因數COSα/ COSαω數值表） |
|
|
|
CNS 5275
1984 Edition Base Tangent Lengths of Helical Gears for Fine Mechanics 精細機械用螺旋齒輪（齒跨距數值表） |
|
|
|
CNS 5274
1984 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 5268
1984 Edition Accuracy of Cylindrical Gear Teeth Tolerance for Errors of Composite 圓柱齒輪輪齒之精度（嚙合複合誤差之公差） |
|
|
|
CNS 10503
1984 Edition Emission-Spectroscopic Analysis for Pig Iron and Cast Iron 生鐵及鑄鐵之發光光譜分析法 |
|
|
|
CNS 5266
1984 Edition Series of Modules for Worm Gear Pairs 齒輪模數（蝸桿蝸輪對） |
|
|
|
CNS 10502
1984 Edition Method for X-Ray Fluorescence Spectrometric Analysis of Pig Iron, Cast Iron, Carbon Steel and Low Alloy Steel 生鐵、鑄鐵、碳鋼及低合金鋼之螢光Ｘ射線分析法 |
|
|
|
CNS 10225
1984 Edition Test Code for Accuracy of Drum Sanders 圓筒砂光機精度檢驗標準 |
|
|
|
CNS 5279
1984 Edition Dimensions of Cylindrical Worm Coordination of Shaft Centre Distances and Transmission Rations of Worm Drives 圓柱蝸桿之尺度及蝸桿傳動機構軸中心距與轉速比之配合 |
|
|
|
CNS 11151
1984 Edition Method of Test for Unit Weight, Yield, and Air Content (Gravimetric) of Concrete 混凝土單位重、拌和體積及含氣量（比重）試驗法 |
Translated |
|
|
CNS 4665
1984 Edition Insert Nuts Heavy Type for Plastics Mouldings and Pressure Die Castings with Dead Hole 嵌入螺帽（長型封閉式，嵌於塑膠製品與壓鑄件內用） |
|
| Find out:6646Items | To Page of: First -Previous-Next -Last | [206] [207] [208] [209] [210] [211] [212] |
