"D C " CNS Standards List |
|
CNS 20858
2018 Edition Ships and marine technology - Maritime port facility security assessments and security plan development 船舶與航運技術－海運港口設施之安全評鑑與安全計畫擬定 |
|
|
|
CNS 10134
2018 Edition Method of Test for Delivered Mass of Aerosol Products 噴霧性產品噴出量試驗法 |
|
|
|
CNS 14431
2018 Edition Method of test for performance of oil/grease interceptor 油脂截留器性能試驗法 |
|
|
|
CNS 4024
2018 Edition Permissible Deviations in Dimensions Without Tolerance Indication (Steel Castings) 一般許可差（鋼鑄件） |
|
|
|
CNS 15402
2018 Edition Green coffee − Defect reference chart 咖啡生豆－缺陷豆參考圖表 |
|
|
|
CNS 10075
2018 Edition Marine Distribution Boards (Fuse Type, Below 250V) 船用分電箱（保險絲型，２５０Ｖ以下） |
|
|
|
CNS 10900
2018 Edition Terminal Blocks for Industrial and Similar Use 工業用接線板 |
|
|
|
CNS 15395
2018 Edition Green coffee − Determination of loss in mass at 105 ℃ 咖啡生豆－於105 ℃之質量損失測定法 |
|
|
|
CNS 14982-1
2018 Edition Miniature fuses - Part 1: Definitions for miniature fuses and general requirements for miniature fuse-links 小型熔線－第１部：小型熔線之定義及小型熔線體之通則 |
|
|
|
CNS 60901
2018 Edition Single-capped fluorescent lamps − Performance specifications 單燈帽螢光燈管－性能要求 |
|
|
|
CNS 15832-2-4
2018 Edition Method of test for coating components − Part 2-4: Component analysis in solvent soluble matter − Alkyd resin 塗料成分試驗法－第2-4部：溶劑可溶物中成分分析－醇酸樹脂 |
|
|
|
CNS 1026
2018 Edition Hand hammers 手用鋼鎚 |
|
|
|
CNS 13382-7
2018 Edition Implants for surgery - Metallic materials - Wrought titanium 6-aluminium 4-vanadium alloy 外科體內植入物－金屬材料－鍛造鈦－６鋁－４釩合金 |
|
|
|
CNS 3-7
2018 Edition Engineering Drawing (Symbols for Steel Construction) 工程製圖（鋼架結構圖） |
|
|
|
CNS 6609
2018 Edition Method of test for meat and meat products - Determination of L-(＋)-glutamic aciD Content 肉及肉製品檢驗法－L－麩胺酸含量之測定 |
|
|
|
CNS 14744
2018 Edition Chlorosulfumated polyethylene insulateD Cables 600V氯磺化聚乙烯橡膠絕緣電纜 |
|
|
|
CNS 1987
2018 Edition Sodium sulfate 硫酸鈉 |
|
|
|
CNS 15569-6
2018 Edition Hydraulic fluid power - Filters elements - Part 6: Evaluation of differential pressure versus flow characteristics 液壓流體動力－過濾器濾心－第6部：差壓對流動特性之評估 |
|
|
|
CNS 10273-2
2018 Edition Rubber, unvulcanized − Determination using a shearing-disc viscometer − Part 2: Determination of pre-vulcanization characteristics 未硫化橡膠－使用剪力-圓盤型黏度計測定－第2部：早期硫化特性 |
|
|
|
CNS 13610
2018 Edition Documentation-Presentation of Scientific and Technical Reports 科學與技術報告撰寫格式 |
|
|
|
CNS 12972-2
2018 Edition Office Machine-Vocabulary-Section 02:Duplicators 事務機器–字彙–第二部：複印機 |
|
|
|
CNS 15130-3-25
2018 Edition Tests on electric cables under fire conditions - Part 3-25 : Test for vertical flame spread of vertically-mounted bunched wires or cables - Category D 電纜之燃燒試驗－第３－２５部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ｄ |
|
|
|
CNS 1439
2018 Edition Methods of Test for Yeast Powders 酵母粉檢驗法 |
|
|
|
CNS 4324
2018 Edition Rounout and undercut for metric thread according to CNS 497~CNS 506 退刀及凹槽（適用於CNS 497~CNS 506之公制螺紋） |
|
|
|
CNS 13936-6
2018 Edition Financial transaction cards-Security architecture of financial transaction systems using integrateD Circuit cards-Part 6:Cardholder Verification 金融交易卡–使用ＩＣ卡的金融交易系統下的安全架構；第６部：持卡者驗證 |
|
|
|
CNS 174
2018 Edition Saddle Key and Tolerance (Cold Drawing) 鍵鋼剖面及偏差（冷拉，用於鞍形鍵） |
|
|
|
CNS 14326
2018 Edition Digital subscriber signalling system no.2 - Connection characteristics negotiation during call/connection establishment phase 第二號數位用戶信號系統－呼叫／連接建立階段中之連接特性協商 |
|
|
|
CNS 12799
2018 Edition Basic Mode Control Procedures-Conversational Information Message Transfer 基本模態控制程序–交談式資訊訊息轉移 |
|
|
|
CNS 14545-7
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 3:Glow-wire ignitability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第３單元：材料引燃性之熾熱線試驗 |
|
|
|
CNS 9994
2018 Edition Rubber Vibration Isolators for Axle and Bolster Springs of Railway Rolling Stock 鐵路車輛軸簧及枕簧用防振橡膠 |
|
| Find out:13340Items | To Page of: First -Previous-Next -Last | [203] [204] [205] [206] [207] [208] [209] |
