"G " CNS Standards List |
|
CNS 11329
2017 Edition Test Method for the Sets of HiGh Strength Hexagon Bolt, Hexagon Nut and Plain Washers for Friction Grip Joints 摩擦接合用高強度六角螺栓、六角螺帽及平墊圈組合件檢驗法 |
|
|
|
CNS 1358
2017 Edition Method of Test for FoldinG Endurance of Paper by Schopper type Tester 紙之蕭波式耐折強度試驗法 |
Translated |
|
|
CNS 6860
2017 Edition Respiratory protective devices − Self-contained open-circuit compressed air breathinG apparatus with full face mask − Requirements, testing, marking 呼吸防護裝置－全面罩壓縮空氣開放式自攜呼吸器－要求、試驗、標示 |
|
|
|
CNS 2671
2017 Edition Galvanized Low Carbon Steel Wire Strand 鍍鋅低碳鋼絞線 |
|
|
|
CNS 1217
2017 Edition Method of practice for manual samplinG of petroleum and petroleum products 石油及其產品手動取樣法 |
|
|
|
CNS 12854
2017 Edition Fire FiGhting Equipment for Liquefied Petroleum Gas Plant Use 液化石油氣設施用消防設備 |
|
|
|
CNS 6127
2017 Edition General Rules for Reliability Assured Discrete Semiconductor Devices 可靠度保證單件半導體裝置總則 |
|
|
|
CNS 9705
2017 Edition General Rules for Emission-Spectroscopic Analysis of Iron and Steel 鐵及鋼之發光光譜分析法通則 |
|
|
|
CNS 6834-8
2017 Edition TestinG methods for rubber and plastics hoses - Part 8: Hydraulic – pressure impulse test without flexing 橡膠管及塑膠管試驗法－第8部：無撓曲液壓脈衝試驗 |
|
|
|
CNS 11399
2017 Edition Method of StraiGht-Beam Ultrasonic Test for Steel Plate for Pressure Vessel Use 壓力容器用鋼板直束法超音波檢驗法 |
|
|
|
CNS 12887-1
2017 Edition Method of Test for Accelerated AGing of Paper and Paperboard - Moist Heat Treatment at 80℃ and 65% R.H. 紙及紙板加速老化試驗法─80℃及65％R.H.濕熱處理 |
Translated |
|
|
CNS 14866-2
2017 Edition Measurement of water flow in fully charGed closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 1132
2017 Edition Pliers and nippers - DiaGonal cutting nippers 夾鉗與剪鉗－對口剪鉗（平口鉗） |
|
|
|
CNS 13982-2
2017 Edition Methods of test for bulk down and feather − Part 2: SamplinG 羽絨羽毛試驗法－第2部：抽樣 |
|
|
|
CNS 15969
2017 Edition Structural requirements of railway vehicle bodies of the locomotives and passenGer rolling stock 機車及客車軌道車輛車體結構要求 |
|
|
|
CNS 15562-7
2017 Edition Stationary traininG equipment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備－第7部：划船機－附加之特定安全要求與試驗法 |
|
|
|
CNS 12865-2
2017 Edition Method of Test for DiGital Microelectronics ( Low Level Output Voltage ) 數位微電子檢驗法（低位準輸出電壓） |
|
|
|
CNS 15767-2-7
2017 Edition PluGs and socket-outlets for household and similar purposes − Part 2-7: Particular requirements for cord extension sets 家用和類似用途插頭及插座－第2-7部：延長用電源線組之特定要求 |
|
|
|
CNS 8473
2017 Edition Pin Allocations for Microprocessor Systems UsinG the Connector for Frequencies Below 3 MHz for Use with Printed Boards 衝頭（打銷用） |
|
|
|
CNS 15581
2017 Edition Grading rules for hardwood sawn lumber 闊葉樹製材分等 |
|
|
|
CNS 4491
2017 Edition LiftinG Eye Bolts 吊環螺釘 |
|
|
|
CNS 12937
2017 Edition Structure of Welded SteelTanks for Petroleum Oil StoraGe 鋼製全熔接石油類儲槽構造 |
|
|
|
CNS 8917
2017 Edition Stationary CentrifuGal Fire Pumps 固定式消防用加壓離心泵 |
|
|
|
CNS 15115
2017 Edition Thin-film terrestrial photovoltaic (PV) modules - DesiGn qualification and type approval 薄膜陸上型太陽光電模組－設計確認和型式認可 |
|
|
|
CNS 9803
2017 Edition WeldinG procedure qualification test for pressure vessels 壓力容器熔接施工方法之確認試驗 |
|
|
|
CNS 6544
2017 Edition Cast steel travellinG wheel for overhead travelling cranes 架空移動起重機用鑄鋼製直行車輪 |
|
|
|
CNS 283
2017 Edition Methods of samplinG and chemical analysis of common salt 工業鹽取樣法及化學分析法 |
|
|
|
CNS 2958
2017 Edition Cast-iron Pipes and FittinGs for Sanitary Equipments 衛生設備用鑄鐵管及管件 |
|
|
|
CNS 13804
2017 Edition Guidance on the Use of the Substitution Method for Measurements of Radiation from Microwave Ovens for Frequencies above 1 GHz 應用置換法測量微波爐１ＧＨｚ以上之輻射指引 |
Translated |
|
|
CNS 12565
2017 Edition Basic Environmental TestinG Procedures Part 2: Tests, Test Db: Damp Heat, Cycle (12+12-Hour Cycle) 環境試驗方法（電氣、電子）–溫濕度循環（１２＋１２小時循環）試驗方法 |
|
| Find out:10068Items | To Page of: First -Previous-Next -Last | [199] [200] [201] [202] [203] [204] [205] |
