"et " CNS Standards List |
|
CNS 15556
2012 Edition Pedometer 計步器 |
|
|
|
CNS 15535
2012 Edition Fluorescent induction lamps - Safety requirements 感應式螢光燈 - 安全性要求 |
|
|
|
CNS 6452
2012 Edition Oil of clove buds [Syzygium aromaticum (L.) Merr. et Perry, syn. Eugenia caryophyllus (Sprengel) Bullock et S. Harrison] 丁香花苞油 |
|
|
|
CNS 15627-3
2012 Edition Ease of operation of everyday products - Part 3: Test method for consumer products 日用品之操作便利性－第3部：消費產品之測試法 |
|
|
|
CNS 6834-2
2012 Edition Testing methods for rubber and plastics hoses - Part 2: Hydrostatic testing 橡膠管及塑膠管試驗法－第2部：耐靜液壓試驗 |
|
|
|
CNS 14866-2
2012 Edition Measurement of water flow in fully charged closed conduits - Meters for cold potable water and hot water - Part 2: Installation requirements 完全充滿的密閉導管內水流量之量測－冷飲水及熱水用水量計－第2部：安裝要求 |
|
|
|
CNS 2539
2012 Edition Canned vegetables 蔬菜類罐頭 |
|
|
|
CNS 15544-2
2012 Edition Load restraint assemblies on road vehicles - Safety - Part 2: Web lashing made from man-made fibres 道路車輛用負載束縛組合－安全規範－第2部：人造纖維製擊帶綑綁器 |
|
|
|
CNS 14310
2012 Edition Method of determining the plastic strain ratio for metallic sheet and strip 薄板金屬材料塑性應變比試驗法 |
|
|
|
CNS 459
2012 Edition Wood − Determination of longitudinal, radial and tangential shrinkage 木材尺度收縮率試驗法 |
|
|
|
CNS 6453
2012 Edition Oil of clove stems [Syzygium aromaticum (L.) Merr. et Perry, syn. Eugenia caryophyllus (Sprengel) Bullock et S. Harrison] 丁香莖油 |
|
|
|
CNS 9504
2012 Edition Methods for estimating average grain size of wrought copper and copper alloys 銅及銅合金展伸材料之晶粒尺度測定法 |
|
|
|
CNS 15561
2012 Edition Method of test for wines - Determination of Oxadixyl 酒類檢驗法－歐殺斯殘留之測定 |
|
|
|
CNS 15138-1
2012 Edition Method of test for determination of phthalates plasticizers in plastic products - Part 1: Gas chromatography/mass spectrometry 塑膠製品中鄰苯二甲酸酯類塑化劑檢驗法－氣相層析質譜法 |
Translated |
|
|
CNS 15562-2
2012 Edition Stationary training equipment − Part 2: Strength training equipment − Additional specific safety requirements and test methods 固定式訓練設備－第2部：力量訓練設備－附加之特定安全要求與試驗法 |
|
|
|
CNS 15625-1
2012 Edition Paragliding equipment – Paragliders – Part 1: Requirements and test methods for structural strength 飛行傘設備－飛行傘－第1部：結構強度要求與試驗法 |
|
|
|
CNS 15555
2012 Edition Method for the simulation of wear before the detection of nickel release from coated metal and combination spectacle frames 金屬眼鏡架鎳釋出測試前磨耗模擬方法 |
|
|
|
CNS 15343
2012 Edition Furniture - Method of test for strength and durability of storage units 家具─收納單元之強度與耐久性測定法 |
|
|
|
CNS 15625-2
2012 Edition Paragliding equipment – Paragliders – Part 2: Requirements and test methods for classifying flight safety characteristics 飛行傘設備－飛行傘－第2部：飛行安全性分類要求與試驗法 |
|
|
|
CNS 14926
2012 Edition Wood − Determination of longitudinal, radial and tangential swelling 木材尺度膨脹率試驗法 |
|
|
|
CNS 9503
2012 Edition Phosphor bronze and nickel silver sheets, plates and strips 磷青銅及鎳銀之板及捲片 |
|
|
|
CNS 15549
2012 Edition Methods of measurement of touch current and protective conductor current 接觸電流與保護導體電流之量測法 |
|
|
|
CNS 15627-2
2012 Edition Ease of operation of everyday products - Part 2: Test method for walk-up-and-use products 日用品之操作便利性－第2部：順手可用產品之測試法 |
|
|
|
CNS 1217
2012 Edition Method of practice for manual sampling of petroleum and petroleum products 石油及其產品手動取樣法 |
|
|
|
CNS 15138
2012 Edition Method of test for determination of plasticizers in plastic products - Gas chromatography 塑膠製品中鄰苯二甲酸酯類塑化劑試驗法－氣相層析法 |
Translated |
|
|
CNS 1254
2012 Edition Canned pickled vegetables 醬菜類罐頭 |
|
|
|
CNS 15562-6
2012 Edition Stationary training equipment − Part 6: Treadmills − Additional specific safety requirements and test methods 固定式訓練設備－第6部：跑步機－附加之特定安全要求與試驗法 |
|
|
|
CNS 4196
2012 Edition General rules for sampling, sample preparation and analytical testing of non-ferrous metals 非鐵金屬材料之試樣採取、製備及分析檢驗通則 |
|
|
|
CNS 15562-7
2012 Edition Stationary training equipment − Part 7: Rowing machines − Additional specific safety requirements and test methods 固定式訓練設備－第7部：划船機－附加之特定安全要求與試驗法 |
|
|
|
CNS 15564-4
2012 Edition ISO general purpose metric screw threads - Tolerances - Part 4: Limits of sizes for hot-dip galvanized external screw threads to mate with internal screw threads tapped with tolerance position H or G after galvanizing ISO一般用途公制螺紋－公差－第4部：鍍鋅後依公差位置H或G攻牙之內螺紋相配合的熱浸鍍鋅外螺紋之限界尺度 |
|
| Find out:7275Items | To Page of: First -Previous-Next -Last | [198] [199] [200] [201] [202] [203] [204] |
