"M " CNS Standards List |
|
CNS 14764
2018 Edition Digital subcriber signalling systeM No.1(DSS1)-Data link layer –ISDN data link layer specification for frame mode bearer services 第一號數位用戶信號系統-資料鏈路層-訊框模式載送服務用之整體服務數位網路資料鏈路層規格 |
|
|
|
CNS 11428
2018 Edition Watt-hour Meter 瓦時計 |
Translated |
|
|
CNS 4394-2
2018 Edition Plastics − Injection Moulding of test specimens of thermoplastic materials − Part 1: General principles, and moulding of multipurpose and bar test specimens 塑膠－熱塑性塑膠射出成型試片－第2部：小型拉伸試驗棒 |
|
|
|
CNS 15130-3-25
2018 Edition Tests on electric cables under fire conditions - Part 3-25 : Test for vertical flaMe spread of vertically-mounted bunched wires or cables - Category D 電纜之燃燒試驗－第３－２５部：垂直敷設成束電線電纜之垂直火焰擴散試驗－類別Ｄ |
|
|
|
CNS 14952-3-2
2018 Edition Guide for the deterMination of thermal endurance properties of electrical insulating materials – Part 3: Instructions for calculating thermal endurance characteristics – section 2: the calculation for incomplete data – verification for test result from gr 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第２章：不完整資料的計算－以包含中間時間到終止點之等量試驗群組驗證試驗結果 |
|
|
|
CNS 14952-3-1
2018 Edition Guide for the deterMination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - section 1: calculations using mean values of normally distributed complete data 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第１章：利用常態分配完整資料的平均值進行計算 |
|
|
|
CNS 10062
2018 Edition NoMinal Dimension of Veneer Jointers 薄板刨邊機之標稱尺度 |
|
|
|
CNS 8691
2018 Edition Marine Hull Cast Steel Gate Valves 船體用鑄鋼閘閥 |
|
|
|
CNS 11321
2018 Edition Method of Test for Absorption and Bulk Specific Gravity of Natural Building Stone 建築用天然石吸水率及體比重試驗法 |
|
|
|
CNS 14802
2018 Edition InforMation technology – System and software integrity levels 資訊技術-系統與軟體完整性層級 |
|
|
|
CNS 10666
2018 Edition Disposable gas-lighter (for cigarette ignition) - Safety requireMents 拋棄式打火機－安全要求 |
Translated |
|
|
CNS 15660-7
2018 Edition Test conditions for nuMerically controlled turning machines and turning centres − Part 7: Evaluation of contouring performance in the coordinate planes 數值控制車床及車削中心機之試驗條件－第7 部：座標平面上循跡性能評估 |
|
|
|
CNS 9488
2018 Edition Marine Bronze 5 kgf / ㎠ Screw-down Check Angle Valves (Union Bonnet Type) 船用青銅管套帽型螺桿止回角閥（5 kgf/㎠） |
|
|
|
CNS 14913
2018 Edition Graphical syMbols for electrical equipment in medical practice 醫電設備之圖形符號 |
|
|
|
CNS 5135
2018 Edition Method of Measurement for Applied Weight of Liquid Adhesives 液狀黏著劑之塗佈量測定法 |
|
|
|
CNS 16090
2018 Edition Test Methods for interconnection protocol for devices in smart home 智慧家庭之裝置互連協定測試法 |
|
|
|
CNS 1439
2018 Edition Methods of Test for Yeast Powders 酵母粉檢驗法 |
|
|
|
CNS 13731
2018 Edition Integrated Services Digital Network (ISDN) FraMe Switching Bearer Service 整體服務數位網路之訊框交換載送服務 |
|
|
|
CNS 14285
2018 Edition Polyethylene FoaM for Heat Insulating 聚乙烯絕緣聚氯乙烯被覆﹝PE-PVC﹞引進線 |
|
|
|
CNS 14151
2018 Edition Line transMission of non-telephone signals - Procedures for establishing communication between threeor more audiovisual terminals using digital channels up to 2Mbit/s 非電話信號之線傳輸–使用可達２Ｍｂｐｓ數位通道建立三部或以上視聽終端機間通訊之程序 |
|
|
|
CNS 15395
2018 Edition Green coffee − DeterMination of loss in mass at 105 ℃ 咖啡生豆－於105 ℃之質量損失測定法 |
|
|
|
CNS 14360
2018 Edition Broadband integrated services digital network (B-ISDN)-Functional description of the B-ISDN user part (B-ISUP) of signalling systeM no.7 寬頻整體服務數位網路－第七號信號系統寬頻整體服務數位網路使用者部之功能描述 |
|
|
|
CNS 8075
2018 Edition Mtheod of Test for Building Components (Concrete Panels for Roofs) 建築用組件（混凝土屋頂嵌板）檢驗法 |
|
|
|
CNS 15568
2018 Edition Protecting EquipMent and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 15569-1
2018 Edition Hydraulic fluid power - Filter eleMents - Part 1: Verification of collapse/burst pressure rating 液壓流體動力－過濾器濾心－第1部：查證崩潰/爆裂壓力額定值 |
|
|
|
CNS 13796
2018 Edition General Aspects and Principles Relating to RecoMmendations on ISDN User-Network Interface-Reference Configurations 整體服務數位網路用戶與網路間介面概觀與原則–參考組態 |
|
|
|
CNS 15710-3
2018 Edition Effects of current on huMan beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
|
|
CNS 15691-1
2018 Edition Aseptic processing of health care products − Part 1: General requireMents 健康照護產品之無菌操作－第 1 部:一般要求 |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 13382-6
2018 Edition IMplants for surgery - Metallic materials - Cobalt-chromium-molybdenum casting alloy 外科體內植入物－金屬材料－鑄造鈷-鉻-鉬合金 |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [193] [194] [195] [196] [197] [198] [199] |
