"An " CNS Standards List |
|
CNS 7962
2017 Edition Test Code for PerformAnce of Numerically Controlled Table Type Horizontal Boring Machines 數值控制床台型臥式搪床動態檢驗法 |
|
|
|
CNS 6834-3
2017 Edition Testing methods for rubber And plastics hoses - Part 3: Determination of resistance to vacuum 橡膠管及塑膠管試驗法－第3部：耐負壓試驗 |
|
|
|
CNS 14673
2017 Edition Interference to mobile radiocommunications in the presence of impulsive noise - Methods of judging degradation And measures to improve performance 脈衝性雜訊對行動無線通信的干擾－產品劣化的判定方式及其性能的改善方法 |
|
|
|
CNS 12902
2017 Edition Analog Interconnection of Television Receivers and Electronic Equipment(21 pin) 電視接收機與類比周邊設備間之相互連接（２１梢多梢連接器） |
|
|
|
CNS 7748
2017 Edition Method of Test for Viscosity of Pulp ( CAnnon -Fenske Capillary Viscometer Method ) 紙漿黏度試驗法（Ｃａｎｎｏｎ–Ｆｅｎｓｋｅ毛細管黏度計法） |
Translated |
|
|
CNS 7383
2017 Edition Stainless steel boiler And heat exchanger tubes 鍋爐及熱交換器用不銹鋼鋼管 |
|
|
|
CNS 11573
2017 Edition Method of Test for Low Frequency (Below 3MHz) Electrical Connectors (TP-50 SAnd and Dust Test) 頻率３ＭＨｚ以下電連接器檢驗法（細砂與塵埃試驗ＴＰ–５０） |
|
|
|
CNS 11942-6
2017 Edition Methods for determination of nickel in copper And copper alloys 銅及銅合金中鎳定量法 |
|
|
|
CNS 3005
2017 Edition Method of Test for Diesel Engine of ConstAnt Speed 定速回轉柴油發動機性能檢驗法 |
|
|
|
CNS 7290
2017 Edition Methods for Determination of Gold And Silver in Crude Bullions 粗金銀錠中金及銀定量法 |
|
|
|
CNS 1108
2017 Edition AdvAnced Saws for Carpenter 木工用前拉鋸 |
|
|
|
CNS 146
2017 Edition Height of Shaft, for Driving And Driven Lines 軸心高度，主動機及從動機 |
|
|
|
CNS 1109
2017 Edition Two-mAn Saws 雙人用長鋸 |
Translated |
|
|
CNS 15966
2017 Edition Packaging − Child resistAnt packaging − Mechanical test methods for reclosable child resistant packaging systems 包裝−防止兒童開拆之包裝−防止兒童開拆之可重複包裝系統機械試驗法 |
|
|
|
CNS 213
2017 Edition Stub Drills with Straight ShAnk and Tenon Drive 驅動榫直柄短鑽頭 |
Translated |
|
|
CNS 9462
2017 Edition Test Code for PerformAnce of Bed Type Horizontal Milling Machines 床台型臥式銑床動態檢驗法 |
Translated |
|
|
CNS 14694-2
2017 Edition Audio , video And audiovisual systems-interconnections and matching values Part 2：21-pin connector for video systems-application No.2 聲音、影像及視聽系統之互連與匹配值－第２部：影像系統適用之２１針連接器－第２類應用 |
|
|
|
CNS 9475
2017 Edition Test Code for PerformAnce of Numerically Controlled Turret and Single Spindle Drilling Machines with Vertical Spindle 數值控制立式六角及單軸鑽床動態檢驗法 |
|
|
|
CNS 13006
2017 Edition MAG Welding Solid Wire for Molybdenum Steel And Chromium Molybdenum Steel 鉬鋼及鉻鉬鋼ＭＡＧ熔接用實心鋼線 |
|
|
|
CNS 366-9
2017 Edition Safety requirements for cycles − Part 9: Saddles And seat-post test methods 自行車安全要求－第9部：座墊及座桿測試法 |
|
|
|
CNS 11619
2017 Edition General Rules for X-Ray Fluorescence Spectrometric Analysis 螢光Ｘ射線分析法總則 |
|
|
|
CNS 547
2017 Edition Electric fAn (desk and wall mounting type) 電扇(桌上型及壁掛型) |
|
|
|
CNS 12650
2017 Edition CAnned mixed congee 粥類罐頭 |
|
|
|
CNS 3610
2017 Edition Two-Flute End Mills with Straight ShAnk 兩刃直柄端銑刀 |
Translated |
|
|
CNS 7345
2017 Edition HAnd Hoe Triangular Shaped 三角鋤 |
|
|
|
CNS 14309
2017 Edition Documentation-Presentation of contributions to periodicals And other serials 期刊及連續性出版品文章編排格式 |
|
|
|
CNS 60227-1
2017 Edition Polyvinyl chloride insulated cables of rated voltages up to And including 450/750V − Part 1: General requirements 額定電壓450/750 V以下聚氯乙烯絕緣電纜－第1 部：一般要求 |
|
|
|
CNS 5507
2017 Edition Rolling Bearings; Bearing with Spherical Outside Surface And Extended Inner Ring Width, Insert bearings 嵌入夾緊滾動軸承（具球面外環與加寬內環） |
|
|
|
CNS 5376-18
2017 Edition Iron ores─Methods for determination of vAnadium content 鐵礦石－釩定量法 |
|
|
|
CNS 15876-2
2017 Edition Specification And qualification of welding procedures for metallic materials − Welding procedure tests − Part 2: Arc welding of aluminium and its alloys 金屬材料銲接程序規範書及其檢定－銲接程序試驗－第2部：鋁及鋁合金的電弧銲接 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [169] [170] [171] [172] [173] [174] [175] |
