"On " CNS Standards List |
|
CNS 4421
2017 Edition Seating Bolts and COnical Spring Washers for Clamping 夾緊用座螺栓與錐形彈簧墊圈 |
|
|
|
CNS 14630
2017 Edition Structural cOniferous sawn lumber 針葉樹結構用製材 |
|
|
|
CNS 14623-2
2017 Edition SterilizatiOn of health care products-chemical indicators-Part 2：Test equipment and methods 保健產品之滅菌─化學指示劑─第二部分：測試設備與方法 |
|
|
|
CNS 4551
2017 Edition Gas Cylinders; Thread for Nozzles, Neck Rings and ProtectiOn Caps 瓦斯瓶用螺紋 |
|
|
|
CNS 13004
2017 Edition Method of Welding Procedure QualificatiOn Test for Stainless-clad steels 不銹鋼包層鋼板熔接施工程序確認試驗法 |
|
|
|
CNS 1411
2017 Edition COntainer for Lead Acid Batteries 鉛蓄電池用外殼 |
|
|
|
CNS 14466-14
2017 Edition Audiovisual,video and televisiOn equipment and systems. Part14:Audio striped card system 視聽．影像及電視設備與系統-第１４部：聲音磁條卡片系統 |
|
|
|
CNS 13418
2017 Edition Method of Test for Brightness for Mineral Fillers and Pigments for Paper Making (45° / 0° DirectiOnal Tester) 造紙用礦物質填料及顏料白度試驗法（４５° ／０°定向白度計法） |
Translated |
|
|
CNS 3957
2017 Edition Method of Test for VinylOn Sewing Thread 維尼龍縫線檢驗法 |
|
|
|
CNS 16015-1
2017 Edition TransportatiOn of dangerous goods − Part 1: Requirement for the construction and testing of packagings 危險貨物之運輸－第1部：包裝物之構造與試驗要求 |
|
|
|
CNS 5062
2017 Edition DirectiOn of Operation of Machine Tool Controls 工具機之操作方向 |
|
|
|
CNS 9493
2017 Edition Wire Ropes for AerOnautical Use 航空器用鋼纜 |
|
|
|
CNS 11089
2017 Edition BrOnze Screwed Gate Valves (15 kgf/㎠) 青銅螺紋口閘閥（15 kgf/㎠） |
Translated |
|
|
CNS 13982-6
2017 Edition Methods of test for bulk down and feather − Part 6: DeterminatiOn of the acidity (pH value) 羽絨羽毛試驗法－第6部：酸度(pH值)測定法 |
|
|
|
CNS 13621
2017 Edition Polyamide (NylOn) Textured Yarns 聚醯胺樹脂接線盒 |
Translated |
|
|
CNS 5968
2017 Edition BrOnze Screwed Lift Check Valves (10kgf/c㎡) 青銅螺紋口升降型止回閥（10 kgf/㎠） |
|
|
|
CNS 14492-4
2017 Edition Methods of measurement On radio receivers for various classes of emission-Part4:Receivers for frequency-modulated sound broadcasting emissions 不同發射類別之無線電接收機的量測方法-第4部:調頻聲音廣播發射適用的接收機 |
|
|
|
CNS 15187-6
2017 Edition Low-voltage fuses - Part 6: Supplementary requirements for fuse-links for the protectiOn of solar photovoltaic energy systems 低電壓熔線－第6部：太陽光電 能源系統保護用熔線鏈之補充規定 |
|
|
|
CNS 15481-3
2017 Edition Road vehicles - EnvirOnmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads 道路車輛－電機電子配備環境條件與試驗－第３部：機械負載 |
|
|
|
CNS 5771
2017 Edition Thermistor Disks, NOn - Insulated (Style TDX) 盤形無絕緣熱敏電阻器（型號ＴＤＸ） |
|
|
|
CNS 62282-3-100
2017 Edition Fuel cell technologies − Part 3-100: StatiOnary fuel cell power systems − Safety 燃料電池技術－第3-100部：定置型燃料電池發電系統－安全 |
|
|
|
CNS 3618
2017 Edition Single-Phase InductiOn Motors(under 100 Watt) １００瓦以下單相感應電動機 |
Translated |
|
|
CNS 4173
2017 Edition COnveyor Chains, Attachments and Chain Wheels 輪送機鏈條、配件及鏈輪 |
|
|
|
CNS 4481
2017 Edition HexagOn Socket Set Screws with Cone End 六角承窩無頭錐形端固定螺釘 |
|
|
|
CNS 9240
2017 Edition Method of Test for Low Freguency(Below 3 MHz) Electrical COnnectors(TP - 18 Visual and Dimensional Inspection) 頻率３ＭＨｚ以下電連接器檢驗法（外觀及尺度檢查ＴＰ–１８） |
|
|
|
CNS 11570
2017 Edition Remote COntrol Relays and Remote Control Switches 遙控電驛及遙控開關 |
|
|
|
CNS 14180
2017 Edition Lot cOntrol tests for digital transmitter and receiver modules used for optical fiber communication 光纖通信用數位傳輸和接收模組之批品質控制測試 |
|
|
|
CNS 15985-2
2017 Edition QualificatiOn testing of welders − Fusion welding – Part 2: Aluminum and aluminum alloys 銲工檢定試驗－熔融銲接－第2部：鋁及鋁合金 |
|
|
|
CNS 12291
2017 Edition General Rules for Reliability Assured Fixed CarbOn Composition Resistors 可靠度保證混合碳固定電阻器總則 |
|
|
|
CNS 7197
2017 Edition Basic DimensiOns of 5 kgf/㎠ Ferrous Materials Pipe Flanges 鐵金屬製管凸緣基準尺度（5 kgf/㎠） |
|
| Find out:7841Items | To Page of: First -Previous-Next -Last | [167] [168] [169] [170] [171] [172] [173] |
