"an " CNS Standards List |
|
CNS 13787
2017 Edition Methods of Test for Tear Resistance of Plastic Films and Sheets 塑膠薄膜及薄片之撕裂強度試驗法 |
Translated |
|
|
CNS 4553
2017 Edition Rounded Trapezoidal Thread; Limits of Sizes and Deviations; Tolerances and Permissible Weal of Thread Gauges 圓角梯形螺紋（螺紋限界尺寸與偏差；螺紋量規之公差與許可磨損） |
|
|
|
CNS 13013
2017 Edition Copper and Copper Alloy Rods and Wires for Inert Gas Shielded Arc Welding 銅及銅合金ＴＩＧ熔接、ＭＩＧ熔接用熔接棒及熔接銅線 |
|
|
|
CNS 502
2017 Edition ISO Metric Fine Screw Threads (Diameters from 12 to 80mm and Pitch 1.5mm) 公制細螺紋5（ISO制）（標稱直徑12至80公釐，螺距1.5公釐） |
|
|
|
CNS 13064
2017 Edition Methods of Test for Specific Gravity of Epoxy Resins and Hardeners 環氧樹脂及硬化劑比重測定法 |
|
|
|
CNS 13192
2017 Edition Test Methods for Performance and Accuracy of Band Saw Stretchers 帶鋸片伸整機之性能試驗及精度檢驗法 |
|
|
|
CNS 14492-1
2017 Edition Methods of measurement on radio receivers for various classes of emission-Part1:General considerations and methods of measurement,including audio-frequency measurements 不同發射類別之無線電接收機的量測方法-第1部:概論及含括音頻量測在內的量測方法 |
|
|
|
CNS 13092
2017 Edition Measuring Method for LED Outdoor Display Panels 發光二極體顯示幕（戶外用）量測法 |
|
|
|
CNS 3633
2017 Edition Basic Environmental Testing Procedures Part 2: Tests, Test N: Change of Temperature 環境試驗法（電氣、電子）–溫度變化試驗 |
|
|
|
CNS 11093
2017 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated and Sheated Cables: VVF) 屋內配線用接線盒〔平型聚氯乙烯絕緣聚氯乙烯被覆電纜（ＶＶＦ用）〕 |
|
|
|
CNS 14812
2017 Edition Corrosion of metals and alloys — Determination of dezincification resistance of brass 金屬及合金之腐蝕─黃銅耐脫鋅測定法 |
|
|
|
CNS 11071
2017 Edition Emission-Spectroscopic analysis for Carbon Steel and Low Alloy Steel 碳鋼及低合金鋼之發光光譜分析法 |
|
|
|
CNS 4369
2017 Edition Round Thread with Clearance and Flat Flank with Pitch 7 mm; Nominal Sizes 圓螺紋（具有間隙、淺螺腹，螺距為７ｍｍ之標稱尺寸） |
|
|
|
CNS 14782
2017 Edition Manipulating industrial robots —Test equipment and metrology methods of operation for robot performance evaluation 工業用機器人性能評估作業之測試儀器與量測方法 |
|
|
|
CNS 4421
2017 Edition Seating Bolts and Conical Spring Washers for Clamping 夾緊用座螺栓與錐形彈簧墊圈 |
|
|
|
CNS 14801
2017 Edition Method of test for water resistance of material used in protective clothing (Impact penetration test) 防護衣材料防水性試驗法－衝擊穿透試驗 |
|
|
|
CNS 14471
2017 Edition Method of test for sulfur in petroleum products − High temperature combustion and IR detection 石油產品硫含量試驗法－高溫燃燒與紅外線檢測 |
|
|
|
CNS 1130
2017 Edition Pliers and nippers - Engineer's and lineman's pliers 夾鉗與剪鉗－一般技術要求 |
|
|
|
CNS 13063
2017 Edition General Rules for Methods of Test for Epoxy Resins and Hardeners 環氧樹脂及硬化劑試驗法總則 |
|
|
|
CNS 13747
2017 Edition Method of Test for Unplasticized Polyvinyl Chloride Pipes with Polyethylene Lining for Wastewater and General Uses 污水及一般用內襯聚乙烯之聚氯乙烯塑膠硬質管檢驗法 |
Translated |
|
|
CNS 5508
2017 Edition Rolling Bearings; Bearings with Spherical Outside Surface and Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
|
|
|
CNS 13350-9
2017 Edition The Safety Code of Mechanical Parking Lot Devices (Multi Stage Type) 機械式停車場安全標準（多段式停車裝置） |
|
|
|
CNS 12844
2017 Edition Method of Test for Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布檢驗法 |
Translated |
|
|
CNS 11446-1
2017 Edition Method of measurement on receives for television broadcast transmission - Part 1: General considerations - Measurements at radio and video frequencies 電視廣播傳輸接收機之量測方法-第一部:概論-射頻及視頻之量測 |
|
|
|
CNS 177
2017 Edition Flat Fitted Key and Its Seat (for Cylindrical Shaft End) 配合平鍵及槽（用於柱軸梢） |
|
|
|
CNS 16015-2
2017 Edition Transportation of dangerous goods − Part 2: Dangerous goods list 危險貨物之運輸－第2部：危險貨物表 |
|
|
|
CNS 5274
2017 Edition Base Tangent Lengths of Spur Gears for Fine Mechanics 精細機械用正齒輪（齒跨距數值表） |
|
|
|
CNS 4790-5
2017 Edition Glossary of terms used in pulp and paper industry ─ Terms of pulp, paper or board properties 紙漿與紙詞彙─紙漿、紙或紙板之性質及試驗名詞 |
|
|
|
CNS 13982-6
2017 Edition Methods of test for bulk down and feather − Part 6: Determination of the acidity (pH value) 羽絨羽毛試驗法－第6部：酸度(pH值)測定法 |
|
|
|
CNS 5977
2017 Edition High - Speed Steel Blades for Machine and Shell Reamers with Screwed - on Blades 高速鋼刀片–螺釘固定式，機用鉸刀，殼形鉸刀 |
|
| Find out:7408Items | To Page of: First -Previous-Next -Last | [154] [155] [156] [157] [158] [159] [160] |
