"In " CNS Standards List |
|
CNS 14545-6
2018 Edition Fire hazard testIng-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 13612
2018 Edition GuidelInes for Planning and Design of Public Library Building and Facilities 公共圖書館建築設備 |
|
|
|
CNS 62133-1
2018 Edition Secondary cells and batteries contaIning alkaline or other non-acid electrolytes − Safety requirements for portable sealed secondary cells, and for batteries made from them, for use in portable applications − Part 1: Nickel systems 含鹼性或其他非酸性電解質之二次單電池及電池組－用於可攜式應用之可攜式封裝型二次單電池及由其所組成的電池組之安全要求－第1部：鎳系 |
|
|
|
CNS 4996
2018 Edition Method of Test for ReInforced Concrete monhole Blocks for Sewerage Work 下水道用鋼筋混凝土人孔井壁檢驗法 |
Translated |
|
|
CNS 14213-4
2018 Edition Information technology - Open systems interconnection - Procedures for the operation of OSI registration authorities - Part 4: Register of VTE profiles 資訊技術–開放系統互連–開放系統互連註冊機構作業程序–第４部：虛擬終端機環境規範之註冊 |
|
|
|
CNS 15620-5
2018 Edition Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining clearance and creepage distances equal to or less than 2 mm 低電壓系統下設備之絕緣協調－第5 部： 決定2 mm 以下空間距離及沿面距離之詳盡方法 |
|
|
|
CNS 14155
2018 Edition Transmission of non-telephone signals - Frame-synchronous control and Indication signals for audiovisual systems 非電話信號之傳輸–視聽系統之訊框同步控制與指示信號 |
|
|
|
CNS 15660-8
2018 Edition Test conditions for numerically controlled turnIng machines and turning centres − Part 8: Evaluation of thermal distortions 數值控制車床及車削中心機之試驗條件－第8 部：熱變形之評估 |
|
|
|
CNS 9691
2018 Edition Information Processing Systems-Vocabulary ( Part 5 : Representation of Data ) 資訊處理系統–詞彙（第５部：資料之表示方法） |
|
|
|
CNS 10688
2018 Edition Interface Between Data Terminal Equipment and Data Circuit-Terminating Equipment Employing Serial Binary Data Interchange - Functional Description of Interchange Circuit 資料終端設備與資料電路終端設備間互換用串列二進資料之介面–互換電路的功能敘述 |
|
|
|
CNS 13010
2018 Edition StaInless steel tubular cored wires and rods for arc welding 電弧銲接用不銹鋼包藥銲線及包藥填料棒 |
|
|
|
CNS 14133
2018 Edition Information Technology - Open Systems Interconnection - Service Definition for the commitment, concurrency and recovery service element 資訊技術–開放系統互連–承諾、併作及復原服務元件用服務定義 |
|
|
|
CNS 13524
2018 Edition Standard Representation of Latitude, Longitude and Altitude for Geographic PoInt Locations 地理點位置之經度緯度及海拔高度之標準表示法 |
|
|
|
CNS 12600
2018 Edition Adhesives for wall and ceilIng boards 牆板及天花板用接著劑 |
|
|
|
CNS 14148
2018 Edition LIne transmission of non-telephone signals - Framework for recommendations for audiovisual services 非電話信號之線傳輸–視聽服務標準框架 |
|
|
|
CNS 12365
2018 Edition Alphanumeric Character Sets for Optical Recognition - Part II : Character Set OCR-B-Shapes and Dimensions of the PrInted Image 光學辨識用文數字集–第二部，ＯＣＲ–Ｂ字集–印出影像之形狀與尺度 |
|
|
|
CNS 8152
2018 Edition Green coffee − DetermInation of moisture content 咖啡生豆－水分含量測定法 |
|
|
|
CNS 979
2018 Edition Method of Test for Canned Food-Inspection for Extraneous Matters 食品罐頭檢驗法–異物之檢查 |
Translated |
|
|
CNS 4735-1
2018 Edition 50Ω and 75Ω radio-frequency coaxial cables Part 1：General requirements and measurIng methods 50Ω及75Ω射頻同軸電纜－第1部：通則與測試方法 |
|
|
|
CNS 14168-2
2018 Edition Information technology-Framework and taxonomy of International Standardized Profiles-Part 2: Principles and Taxonomy for OSI profiles 資訊技術–國際標準規範之框架及分類–第２部：開放系統互連之原則與分類 |
|
|
|
CNS 13832
2018 Edition Broadband-Integrated services digital networks (B-ISDN) ATM adaptation layer (AAL) specification 寬頻整體服務數位網路–非同步傳送模式適應層規格 |
|
|
|
CNS 3037
2018 Edition MixIng rooms, moist cabinets, moist rooms, and water storage tanks used in the testing of hydraulic cements and concretes 水硬性水泥及混凝土試驗用拌和室、水槽、濕養櫃及濕養室 |
|
|
|
CNS 4234-3
2018 Edition Mechanical properties of corrosion-resistant staInless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress 不銹鋼結件之機械性質－第３部：無拉應力下之固定螺釘及類似結件 |
|
|
|
CNS 9601
2018 Edition MarIne Reflector Lamp Type Flood Lights 船用汎光燈（反射型投射電燈泡式） |
|
|
|
CNS 15569-2
2018 Edition Hydraulic fluid power – Filter elements – Part 2: Verification of fabrication Integrity and determination of the first bubble point 液壓流體動力－過濾器濾心－第2部：查證製作完整性及測定首次起泡點 |
|
|
|
CNS 21003-7
2018 Edition Multilayer pipIng systems for hot and cold water installations inside buildings − Part 7: Guidance for the assessment of conformity 建築物內冷熱水裝置用多層管配管系統－第7部：符合性評鑑指引 |
|
|
|
CNS 13926-6
2018 Edition Information technology-Open systems interconnection-Distributed transaction processing-Part 6:unstructured data transfer 資訊技術–開放系統互連–分散式交易處理–第６部：非結構資料轉送 |
|
|
|
CNS 10367
2018 Edition Method of test for oversized particles In emulsified bitumen (Sieve test) 乳化瀝青篩析試驗法 |
|
|
|
CNS 3746-1
2018 Edition Series 1 freight contaIners - Specification and testing - Part 1：General cargo containers for general purposes 第一類貨櫃－規格與試驗－第１部：通用貨櫃 |
|
|
|
CNS 4670-6
2018 Edition Specified Items for MachIne Tools - Multiple Spindle Automatic Lathes 工具機規範之項目–多軸自動車床 |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [153] [154] [155] [156] [157] [158] [159] |
