"2,4 " CNS Standards List| Assembly tools | Involute Splines | Ring Gauge | Bronze Flanged | Method | Spiral Wound | Engineering Drawing | Chemical Reagent | |
|
CNS 14964-22
2020 Edition Wheelchair − Part 22: Set-up procedures 輪椅－第22部：設定程序 |
|
|
|
CNS 12514-11
2020 Edition Fire-resistance tests − Elements of building construction − Part 11: Specific requirements for the assessment of fire protection to structural steel elements 建築物構造構件耐火試驗法－第11部：鋼結構構件防火被覆評估特定要求 |
|
|
|
CNS 61427-2
2020 Edition Secondary cells and batteries for renewable energy storage − General requirements and methods of test − Part 2: On-grid applications 再生能源儲能用二次單電池及電池組－一般要求及試驗法－第2部：併網應用 |
|
|
|
CNS 11742
2020 Edition Method of Test for Reheat Shrikage of Insulating Fire Bricks 絕熱耐火磚再熱收縮試驗法 |
|
|
|
CNS 4240
2020 Edition Electroplated Coating of Bolts, Screws and Nuts 螺栓、螺釘、螺帽之電鍍層 |
|
|
|
CNS 15212-4
2020 Edition Clinical Thermometers - Part 4: Performance of electrical thermometers for continuous measurement 電子體溫計－第４部：用於連續量測之電子體溫計的性能 |
|
|
|
CNS 4242
2020 Edition Widths Across Flats and Widths Across Corners for Bolts, Screws and Nuts 螺栓、螺釘、螺帽之對面寬度及對角寬度 |
|
|
|
CNS 14103-2
2020 Edition Prosthetics and orthotics - Vocabulary - Part 1: General terms of external limb prostheses and external orthoses 義肢學與矯具學－詞彙－第２部：外用義肢與其穿戴者之術語 |
|
|
|
CNS 14490-2
2020 Edition Robots and robotic devices − Safety requirements for industrial robots − Part 2: Robot systems and integration 機器人及機器人裝置－工業機器人之安全要求－第2 部：機器人系統及整合 |
|
|
|
CNS 14103-3
2020 Edition Prosthetics and orthotics - Vocabulary - Part 2: Terms relating to external limb prostheses and wearers of these prostheses 義肢學與矯具學－詞彙－第３部：外用矯具之術語 |
|
|
|
CNS 4372
2020 Edition Round Thread with Clearance and Steep Flank with Pitch 7mm (Limits of Sizes and Deviations--Tolerances and Permissible Wear of Thread Gauges) 圓螺紋（具有間隙，深螺腹，螺距７ｍｍ之螺紋限界尺寸和偏差螺紋量規之公差和許可磨損） |
|
|
|
CNS 14829
2020 Edition Helical compression springs for rolling stocks 軌道車輛用壓縮螺旋彈簧 |
|
|
|
CNS 14824
2020 Edition Method of test for detailed analysis of petroleum naphthas through n-nonane by capillary gas chromatography 正壬烷以下石油腦成分試驗法(毛細管柱氣相層析法) |
|
|
|
CNS 14243
2020 Edition Method of test for smoke point of kerosine and aviation turbine fuels 煤油及航空燃油發煙點試驗法 |
|
|
|
CNS 14142
2020 Edition Methods of test for adaptation assessment of fine ceramics under high temperature and high pressure 精密陶瓷高溫、高壓環境適應性試驗法 |
|
|
|
CNS 3542
2020 Edition Forged shackles for general lifting purposes – Dee shackles and bow shackles 一般起重吊掛用鍛造鉤環－D形鉤環及弓形鉤環 |
|
|
|
CNS 3742
2020 Edition Freight containers - Coding,identification and marking 貨櫃之代碼、識別及標誌 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 15832-4-2
2020 Edition Method of test for paint components − Part 4-2: Analysis for components emitted from film − Volatile organic compounds 塗料成分試驗法－第4-2 部：塗膜釋出成分分析－揮發性有機化合物(VOC) |
|
|
|
CNS 14247
2020 Edition Method of test for naphthalene hydrocarbons in aviation turine fuels by ultravioet spectrophotometry 航空燃油中萘族烴試驗法﹝紫外線光譜法﹞ |
|
|
|
CNS 8411-2
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Abrasive jet test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－第２部：噴射磨耗試驗法 |
|
|
|
CNS 6324
2020 Edition Switches of Back-up Lamps for Automobiles 汽車倒車燈開關 |
|
|
|
CNS 15423-3
2020 Edition Equipment for water supply service – Part 3: Test methods of water hammer 自來水用器具－第3部：水鎚試驗法 |
|
|
|
CNS 14298
2020 Edition Method of test for determination of benzene, toluene, ethylbenzene, p/m-xylene, o-xylene, C₉ and heavier aromatics, and total aromatics in finished gasoline by gas chromatography 汽油中各種芳香烴測定法（氣相層析法） |
|
|
|
CNS 493
2020 Edition Fine Whitworth Thread (Diameter Ranging From 20 to 189 mm, with Tip Clearance) 韋氏細螺紋（尖端有空隙，直徑自２０至１８９公釐） |
|
|
|
CNS 12835-5
2020 Edition Plastics piping systems for the supply of gaseous fuels − Polyethylene (PE) − Part 4: Valves 燃氣用塑膠配管系統－聚乙烯(PE)－第5部：系統適合度 |
|
|
|
CNS 7024
2020 Edition Cable Terminals for Automobiles (Type CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 3246
2020 Edition Determination of Linean Thermal Expansion of Fired Fine Ceramic and Porcelain Products 已燒製精陶瓷製品線熱膨脹之測定法（膨脹計法） |
|
|
|
CNS 14503-2
2020 Edition Evaluation methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 2: Grid method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第２部：柵格法 |
|
|
|
CNS 15200-4-5
2020 Edition Methods of test for paints - Part 4-5: Visual characteristics of film - Colorimetry (Calculation of colour differences) 塗料一般試驗法－第４－５部：塗膜視覺特性－測色（色差計算） |
|
| Find out:2312Items | To Page of: First -Previous-Next -Last | [10] [11] [12] [13] [14] [15] [16] |
