"L, " CNS Standards List |
|
CNS 3760
2019 Edition Method of Test for Nylon Ropes 尼龍繩索檢驗法 |
|
|
|
CNS 7272
2019 Edition Method of Test for Polypropylene Ropes 聚丙烯繩索檢驗法 |
|
|
|
CNS 10314
2019 Edition 600 V Grade polyethylene insulated wires for electricaL apparatus 電機器具用600 V 聚乙烯絕緣電線 |
|
|
|
CNS 15291
2019 Edition Safety of children’s clothing − Cords and drawstrings on children’s clothing − Specifications 兒童衣物安全規範－兒童衣物之繩帶與拉繩 |
|
|
|
CNS 14831
2019 Edition Method of test for oxygenates and paraffin , olefin , naphthene , aromatic（O-PONA）hydrocarbon types in low-olefin spark ignition engine fuels by gas chromatography 低烯烴汽油含氧化物、飽和烴、烯烴、環烷烴及芳香烴（O-PONA）測定法（氣相層析法） |
|
|
|
CNS 15660-3
2019 Edition Test conditions for numerically controlled turning machines and turning centres − Part 3: Geometric tests for machines with inverted verticaL workholding spindles 數值控制車床及車削中心機之試驗條件－ 第3部：倒立式工件夾持主軸工具機之幾何試驗 |
|
|
|
CNS 2688
2019 Edition Felt 襯墊用毛氈 |
|
|
|
CNS 14900
2019 Edition EssentiaL oils - General rules for packaging, conditioning and storage 精油－包裝材料、調節及儲存通則 |
|
|
|
CNS 1235
2019 Edition Method of test for bleeding of concrete 混凝土泌水試驗法 |
|
|
|
CNS 15200-9-2
2019 Edition Methods of test for paints – Part 9-2: Coating powders – Inclined-plane flow test 塗料一般試驗法－第9-2 部：粉體塗料－斜面流動性試驗 |
|
|
|
CNS 12103
2019 Edition Method of test for formaldehyde content of paper products by acetylacetone 紙製品甲醛含量試驗法(乙醯丙酮法) |
|
|
|
CNS 8944
2019 Edition Method of Test for Tyre Valves for Automobiles 汽車輪胎氣門嘴檢驗法 |
|
|
|
CNS 16109
2019 Edition Test method for current-voltage (I-V) performance measurement of organic photovoltaic (OPV) and dye-sensitized solar celL (DSSC) 有機與染料敏化太陽能電池－ 電流-電壓性能量測試驗法 |
|
|
|
CNS 15758-1
2019 Edition Packaging for terminally sterilized medicaL devices – Part 1: Requirements for materials, sterile barrier systems and packaging systems 最終滅菌醫療器材之包裝－第1 部：材料、無菌屏障系統及包裝系統之要求 |
|
|
|
CNS 14964-25
2019 Edition Wheelchairs − Part 25: Batteries and chargers for powered wheelchairs 輪椅－第25 部：電動輪椅之電池組及充電器 |
|
|
|
CNS 15117
2019 Edition Photovoltaic systems − Power conditioners − Procedure for measuring efficiency 太陽光電系統－電力調節器－量測效率之程序 |
|
|
|
CNS 9487
2019 Edition Bronze Screw down Check Globe Valves for Marine Use (5 kgf / ㎠) (Union Bonnet Type) 船用青銅管套帽型螺桿止回球形閥（5 kgf/㎠） |
|
|
|
CNS 15077-3
2019 Edition Test conditions for machining centres - Part 3 : Geometric tests for machines with integraL indexable or continuous universal heads (vertical Z-axis) 切削中心機之檢驗條件－第３部：具整合型分段指示或連續萬向分度頭之機器幾何檢驗（垂直Ｚ軸） |
|
|
|
CNS 15755-5-4
2019 Edition Conversion tables for units − Part 5-4: Pressure or stress − Millimeter of mercury and millibar 單位換算表－第5-4 部：壓力或應力－毫米汞柱與毫巴 |
|
|
|
CNS 12285
2019 Edition Pressurized explosion-proof construction of electric machineries and apparatuses of mines ( replaced by CNS 3376-0 ) 鋼襯預力混凝土管 |
|
|
|
CNS 13306-1-5
2019 Edition Specification for radio disturbance and immunity measuring apparatus and methods - Part 1-5: Radio disturbance and immunity measuring apparatus - Antenna calibration test sites for 30 MHz to 1000 MHz 射頻擾動和免疫力量測設備與量測方法－第１－５部：射頻擾動和免疫力量測設備－30 MHz至 1000 MHz之天線校正場地 |
|
|
|
CNS 15562-10
2019 Edition Stationary training equipment − Part 10: Exercise bicycles with a fixed wheeL or without freewheel, additional specific safety requirements and test methods 固定式訓練器材－第10部：具固定輪或無自由輪健身車之附加特定安全要求與試驗法 |
|
|
|
CNS 15753
2019 Edition Plastics piping systems for hot and cold water installations − Polypropylene (PP) − Part 7: Guidance for the assessment of conformity 地下排水及排污非壓力塑膠配管系統－聚乙烯(PE) |
|
|
|
CNS 15130-2-2
2019 Edition Tests on electric and opticaL fibre cables under fire conditions − Part 2-2: Test for vertical flame propagation for a single small insulated wire or cable – Procedure for diffusion flame 電纜及光纜之燃燒試驗－ 第2-2部:單條小型絕緣電線或電纜之垂直火焰延燃試驗－ 擴散火焰之程序 |
|
|
|
CNS 11030
2019 Edition Overlaid glulam for decorative use 化粧貼面裝修用集成材 |
|
|
|
CNS 2279
2019 Edition Method of Test for Twisted Nylon Filament of Fishing Nets 漁網用耐綸絲撚線檢驗法 |
|
|
|
CNS 30
2019 Edition Belt drives − Pulleys − Quality, finish and balance 皮帶傳動－皮帶輪－品質、加工及平衡 |
|
|
|
CNS 15077-4
2019 Edition Test conditions for machining centers - Part 4 : Accuracy and repeatability of positioning of linear and rotary axes 切削中心機之檢驗條件－第４部：線性軸與旋轉軸之定位精度與重現性 |
|
|
|
CNS 10273-4
2019 Edition Rubber, unvulcanized − Determinations using a shearing-disc viscometer − Part 4: Determination of the Mooney stress-relaxation rate 未硫化橡膠－使用剪力-圓盤型黏度計－第4 部:木尼應力-鬆弛速率之測定 |
|
|
|
CNS 14004
2019 Edition EnvironmentaL management systems − General guidelines on implementation 環境管理系統－實施之一般指導綱要 |
|
| Find out:14127Items | To Page of: First -Previous-Next -Last | [135] [136] [137] [138] [139] [140] [141] |
