"In " CNS Standards List |
|
CNS 15762-6
2019 Edition Footwear − Test methods for uppers − Part 6: Abrasion resistance of uppers, lInings and insocks 鞋類－鞋面試驗法－第6 部：鞋面、內裡及鞋墊之耐摩損性 |
|
|
|
CNS 15337
2019 Edition Furniture - Method for determInation of stability of upright chairs and stools 家具－椅、凳穩定性測定法 |
|
|
|
CNS 2623
2019 Edition AlumInium Hydroxide 氫氧化鋁 |
|
|
|
CNS 11491
2019 Edition Wall paper and wall coverIngs for decorative finish 壁紙 |
Translated |
|
|
CNS 1414
2019 Edition N-Hexane, for Industrial Use 工業用正己烷 |
Translated |
|
|
CNS 15132
2019 Edition Internet protocol version 6(IPv6) addressing architecture 網際網路協定第６版（ＩＰｖ６）定址架構 |
|
|
|
CNS 60245-2
2019 Edition Rubber Insulated cables − Rated voltages up to and including 450/750 V − Part 2: Test methods 額定電壓450/750 V以下橡膠絕緣電纜－第2部：試驗法 |
|
|
|
CNS 15055
2019 Edition Liquid petroleum products determInation of contamination in middle distillates 中質蒸餾油污染物測定法 |
|
|
|
CNS 15601
2019 Edition Commercial vehicles − Obstacle detection device durIng reversing − Requirements and tests 商用車－倒車障礙物偵測裝置－要求與試驗 |
|
|
|
CNS 15161
2019 Edition Iron and steel - SamplIng and preparation of samples for the determination of chemical composition 鐵及鋼－化學成分定量分析用試樣之採取及製備 |
|
|
|
CNS 2474
2019 Edition Silver BrazIng Filler Metals 銀焊料 |
|
|
|
CNS 11167
2019 Edition Iron and steel-Methods for determInation of vanadium content 鐵及鋼─釩定量法 |
|
|
|
CNS 6341
2019 Edition Thoriated Tungsten Wires and Rods for LightIng and Electronic Equipments 照明及電子設備用釷鎢線及棒 |
|
|
|
CNS 14245
2019 Edition Centrifugal prestressed concrete pole (for communication lIne) 電信用離心法製預力混凝土電桿 |
|
|
|
CNS 12841
2019 Edition Methods of SamplIng for Precious Brazing Filler Metals 貴金屬焊料取樣法 |
|
|
|
CNS 15082
2019 Edition Internet control message protocol (ICMPv6) for the internet protocol version 6 (IPv6) specification 用於ＩＰｖ６規格之網際網路控制訊息協定 |
|
|
|
CNS 6166
2019 Edition Yokes of Adjustable Clevis JoInts for Automobiles 汽車用可調整叉形接頭之叉部 |
|
|
|
CNS 11451
2019 Edition Iron and steel-Methods for determInation of niobium content 鐵及鋼─鈮定量法 |
|
|
|
CNS 14386-14
2019 Edition General rules of chargIng devices for electric motorcycles 電動機器腳踏車--充電設施總則 |
|
|
|
CNS 15638
2019 Edition Rigid cellular plastics – DetermInation of compressive creep under specified load and temperature conditions 硬質發泡塑膠－規定載重與溫度狀態下之壓縮潛變測定法 |
|
|
|
CNS 5320
2019 Edition MountIng Dimensions of Distributors for Automobiles 汽車用分電盤安裝尺度 |
|
|
|
CNS 6956
2019 Edition Tower PackIngs of Acid Resisting Porcelain for Chemical Industry 化學工業用耐酸陶瓷器–反應塔填充物 |
|
|
|
CNS 15094-1
2019 Edition FIne ceramics - Test method for air purification performance of photocatalytic materials - Part 1: Removal of nitric oxide 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第1部：氮氧化物去除性能 |
|
|
|
CNS 14283
2019 Edition 600V rubber Insulated cable ６００Ｖ橡膠絕緣電纜 |
|
|
|
CNS 3111
2019 Edition Method of Hill ClimbIng Test for Motor Cycles 機器腳踏車爬坡能力試驗法 |
|
|
|
CNS 12472
2019 Edition Inspection of Amusements (Airplane Tower) 育樂設備（飛行塔）檢查標準 |
|
|
|
CNS 13641
2019 Edition Method of Test for GraIns-Determination of Wet Gluten by Hand Washing Method 穀類檢驗法–濕麵筋測定（手洗法） |
|
|
|
CNS 6691
2019 Edition Nylon Spun Yarns, Worsted System, UnfInished 尼龍紗（梳毛式，本白紗） |
|
|
|
CNS 3924
2019 Edition RefIned Fish Liver Oil (for Feeding) 精製水產物肝油（飼料用） |
Translated |
|
|
CNS 10712
2019 Edition Diaphragm Gaskets of hydraulic Brake Master CylInder Reservoirs for Automobiles 汽車用液壓煞車總泵貯油槽膜片襯墊 |
|
| Find out:10338Items | To Page of: First -Previous-Next -Last | [118] [119] [120] [121] [122] [123] [124] |
