"m " CNS Standards List| Wire rope | Mountaineering Boots | General Rules | Canned abalone | Method Test | Essential oils | Method test | A mode | |
|
CNS 15200-1-6
2019 Edition Testing methods for paints - Part 1-6: General rule - Temperatures and humidities for conditioning and testing 塗料一般試驗方法－第１－６部：通則－調節與試驗之溫度及濕度 |
|
|
|
CNS 7334
2019 Edition metal Panels for Concrete Form 鋼筋混凝土用金屬模板 |
Translated |
|
|
CNS 60669-2-3
2019 Edition Switches for household and similar fixed electrical installations − Part 2-3: Particular requirements − Time-delay switches (TDS) 家用和類似用途固定式電氣裝置之開關－第2-3部：延時開關(TDS)之個別要求 |
|
|
|
CNS 15196
2019 Edition Salt mist corrosion testing of photovoltaic (PV) modules 太陽光電模組之鹽霧腐蝕試驗 |
|
|
|
CNS 14532
2019 Edition method of test for penetration and split-barrel sampling of soils 貫入試驗及劈管採樣法 |
|
|
|
CNS 10204
2019 Edition method of Test for Fire Fighting Emergency Power Source 消防緊急用自備發電設備檢驗法 |
|
|
|
CNS 15207-4
2019 Edition Road vehicles - Component test methods for electrical disturbances from narrowband radiated electromagnetic energy - Part 4: Bulk current injection (BCI) 道路車輛－窄頻輻射電磁能量之電擾動組件試驗法－第４部：大電流注入 |
|
|
|
CNS 14934-3
2019 Edition Electromagnetic compatibility (EMC) - Limits - Part 3: Limitation of voltage changes, voltage fluctuations and flicker in public low-voltage supply systems, for equipment with rated current ≦16A per phase and not subject to conditional connection 電磁相容－限制值－第3部：每相額定電流在16 A以下且不屬於有條件連接之設備於公共低電壓電源系統中電壓改變、電壓變動及閃爍之限制值 |
|
|
|
CNS 16107-3
2019 Edition Hollow taper interface with flange contact surface − Part 3: Dimensions of shanks for stationary tools 具凸緣接觸面之空心錐度界面－第3部：固定式刀具之刀柄尺度 |
|
|
|
CNS 15027-1
2019 Edition Sound system equipment − Headphones and earphones associated with personal music players − Maximum sound pressure level measurement methodology − Part 1: General method for one package equipment 聲音系統設備－與個人音樂播放器相關之頭戴式耳機及耳戴式耳機－最大聲壓位準量測法－第1部：套裝設備之一般量測法 |
|
|
|
CNS 16112
2019 Edition Specification and qualification of welding procedures for metallic materials − Qualification by adoption of a standard welding procedure specification 金屬材料銲接程序規範書及其檢定－依〝標準銲接程序規範書〞檢定 |
|
|
|
CNS 9612
2019 Edition Aluminium and aluminium alloy forgings 鋁及鋁合金鍛件 |
|
|
|
CNS 15030-12
2019 Edition Classification and labelling of chemicals - Substances and mixtures which, in contact with water, emit flammable gases 化學品分類及標示－禁水性物質 |
Translated |
|
|
CNS 15094-4
2019 Edition Fine ceramics - Test method for air purification performance of photocatalytic materials - Part 4: Removal of formaldehyde 精密陶瓷－光觸媒材料之空氣淨化性能測定法－第4部：甲醛去除性能 |
|
|
|
CNS 1233
2019 Edition method of Test for Flexural Strength of Concrete (Using Simple Beam with Third-point Loading) 混凝土抗彎強度試驗法（三分點載重法） |
Translated |
|
|
CNS 20349-2
2019 Edition Personal protective equipment − Footwear protecting against risks in foundries and welding − Part 2: Requirements and test methods for protection against risks in welding and allied processes 個人防護具－防止鑄造及熔接中風險之鞋類－第2部：防護熔接及類似製程風險之要求事項及試驗方法 |
|
|
|
CNS 11720
2019 Edition methods of Chemical Analysis for Platinum 鉑分析法 |
|
|
|
CNS 16100
2019 Edition Specification and qualification of welding procedures for metallic materials − Qualification based on tested welding consumables 金屬材料銲接程序規範書及其檢定－依〝已認可銲接材料〞檢定 |
|
|
|
CNS 15030-26
2019 Edition Classification and labelling of chemicals - Aspiration hazard 化學品分類及標示－吸入性危害物質 |
Translated |
|
|
CNS 4269
2019 Edition Hot-rolled atmospheric corrosion resisting steels for welded structure 銲接結構用耐候性熱軋鋼料 |
|
|
|
CNS 15089
2019 Edition method of test for acidity in volatile solvents and chemical intermediates used in paint, varnish, lacquer, and related products 油漆、亮光漆及相似物揮發性溶劑及中間物酸度試驗法 |
|
|
|
CNS 16109
2019 Edition Test method for current-voltage (I-V) performance measurement of organic photovoltaic (OPV) and dye-sensitized solar cell (DSSC) 有機與染料敏化太陽能電池－ 電流-電壓性能量測試驗法 |
|
|
|
CNS 15237
2019 Edition Hot-dip 55 % aluminium-zinc alloy-coated steel sheet and coil 熱浸鍍55 %鋁-鋅合金鋼片及鋼捲 |
|
|
|
CNS 745
2019 Edition Classical and narrow V-belts for power transmission 動力傳動用三角橡膠帶 |
|
|
|
CNS 15016-1
2019 Edition Safety of laser products – Part 1: Equipment classification and requirements 雷射產品安全－第1部：設備分級與要求 |
|
|
|
CNS 15711-1
2019 Edition Photovoltaic (PV) module performance testing and energy rating − Part 1: Irradiance and temperature performance measurements and power rating 太陽光電模組性能試驗與能量定額－第1 部： 照射度與溫度性能量測及功率定額 |
|
|
|
CNS 15580-1
2019 Edition Textiles - Determination of formaldehyde - Part 1: Free and hydrolysed formaldehyde (water extraction method) 紡織品－甲醛測定法－第1部 游離及水解甲醛(水萃取法) |
|
|
|
CNS 8644
2019 Edition Liquid-applied compounds for waterproofing membrane coating of buildings 建築用塗膜防水材 |
|
|
|
CNS 3505
2019 Edition Welding consumables − Wire electrodes, wires and rods for welding of aluminium and aluminium alloys − Classification 銲接材料－鋁及鋁合金銲線及填料棒－分類 |
|
|
|
CNS 13280
2019 Edition method of Test for Hazardous Components in Sulfate Fertilizers (Determination of Sulfurous Acid Content) 肥料中有害成分檢驗法（亞硫酸之測定） |
|
| Find out:12524Items | To Page of: First -Previous-Next -Last | [113] [114] [115] [116] [117] [118] [119] |
