CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"et " CNS Standards List

N-Agriculture, Food
CNS 8152    2018 Edition
Green coffee − Determination of moisture content
咖啡生豆-水分含量測定法
Z6-Physical Distribution & Packaging
CNS 10033-3    2018 Edition
Complete,filled transport packages - General rules for the compilation of performance test schedules - Part 3: General rules for performance testing
包裝貨物性能試驗計畫之編擬通則-第3部:評估試驗法通則
C-Electrical Engineering
CNS 14545-6    2018 Edition
Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials
火災危險性試驗-第2部:試驗方法-第1章/第2單元:材料可燃性之熾熱線試驗
X-Information & Communication
CNS 13832    2018 Edition
Broadband-integrated services digital networks (B-ISDN) ATM adaptation layer (AAL) specification
寬頻整體服務數位網路–非同步傳送模式適應層規格
K-Chemical Industry
CNS 3517    2018 Edition
Method of test for water in petroleum products and bituminous materials by distillation
石油產品與瀝青類物質 水分試驗法(蒸餾法)
B-Mechanical Engineering
CNS 15569-2    2018 Edition
Hydraulic fluid power – Filter elements – Part 2: Verification of fabrication integrity and determination of the first bubble point
液壓流體動力-過濾器濾心-第2部:查證製作完整性及測定首次起泡點
K-Chemical Industry
CNS 15606-4    2018 Edition
Plastics − Determination of tensile properties − Part 3: Test conditions for films and sheets
塑膠-抗拉性能測定法-第4部:同向與正交異向性纖維強化塑膠複合材料之試驗條件
C-Electrical Engineering
CNS 15620-5    2018 Edition
Insulation coordination for equipment within low-voltage system – Part 5: Comprehensive method for determining clearance and creepage distances equal to or less than 2 mm
低電壓系統下設備之絕緣協調-第5 部: 決定2 mm 以下空間距離及沿面距離之詳盡方法
L-Textile Industry
CNS 17299-2    2018 Edition
Textiles − Determination of deodorant property − Part 2: Detector tube method
紡織品-消臭性測定-第2部:檢知管法
A-Civil Engineering & Architecture
CNS 10416    2018 Edition
Stretchy asphalt roofing felts (Synthetic fiber base)
抗拉油毛氈
B-Mechanical Engineering
CNS 4234-3    2018 Edition
Mechanical properties of corrosion-resistant stainless steel fasteners - Part 3: Set screws and similar fasteners not under tensile stress
不銹鋼結件之機械性質-第3部:無拉應力下之固定螺釘及類似結件
A-Civil Engineering & Architecture
CNS 3037    2018 Edition
Mixing rooms, moist cabinets, moist rooms, and water storage tanks used in the testing of hydraulic cements and concretes
水硬性水泥及混凝土試驗用拌和室、水槽、濕養櫃及濕養室
C-Electrical Engineering
CNS 4735-1    2018 Edition
50Ω and 75Ω radio-frequency coaxial cables Part 1:General requirements and measuring methods
50Ω及75Ω射頻同軸電纜-第1部:通則與測試方法
A-Civil Engineering & Architecture
CNS 11297    2018 Edition
Method of capping cylindrical concrete specimens
混凝土圓柱試體蓋平法
X-Information & Communication
CNS 12972-5    2018 Edition
Office Machine - Vocabulary - Section 05 : Letter folding machines
事務機器–字彙–第五部:郵件折疊機 
A-Civil Engineering & Architecture
CNS 12383    2018 Edition
Method of test for resistance R-value and expansion pressure of compacted soils
夯實土壤阻力R值及膨脹壓力試驗法
X-Information & Communication
CNS 14233-13    2018 Edition
Information processing - SGML support facilities - Techniques for using SGML - Part 13:Public entity sets for mathematics and science
資訊處理–標準通用標示語言支援設施–標準通用標示語言的使用技術–第13部:數學與科學之公用個體集
Z6-Physical Distribution & Packaging
CNS 2109    2018 Edition
Method of Test for Domestic Use Cement Paper Sacks
內銷用水泥紙袋試驗法
S-Domestic Wares
CNS 16031-1    2018 Edition
Outdoor furniture − Seating and tables for camping, domestic and contract use − Part 1: General safety requirements
戶外家具-露營、家用及公共場所用桌椅-第1部:一般安全要求
Z7-General & Miscellaneous
CNS 2828    2018 Edition
Plastics − Reinforced moulding compounds and prepregs − Determination of apparent volatile-matter content
塑膠-狀態調節及試驗之 標準大氣狀態
K-Chemical Industry
CNS 15101    2018 Edition
Rubber – General procedures for preparing and conditioning test pieces for physical test methods
橡膠-物理試驗用試片製備及狀態調節之一般程序
C-Electrical Engineering
CNS 14952-1    2018 Edition
Guide for the determination of thermal endurance properties of electrical insulating materials - Part 1: General guidelines for ageing procedure and evaluation of test results
電氣絕緣材料之耐熱性測定指引-第1部:老化程序與試驗結果評估之一般導引
B-Mechanical Engineering
CNS 3-14    2018 Edition
Engineering Drawing (Geometrical Tolerancing - Datums and Datum - Systems)
工程製圖(幾何公差–基準及基準系統之標註)
C-Electrical Engineering
CNS 15652-3    2018 Edition
Intelligent lighting systems − Part 3: Field area network interface
智慧照明系統- 第3部:場域網路介面
K-Chemical Industry
CNS 10367    2018 Edition
Method of test for oversized particles in emulsified bitumen (Sieve test)
乳化瀝青篩析試驗法
X-Information & Communication
CNS 13731    2018 Edition
Integrated Services Digital Network (ISDN) Frame Switching Bearer Service
整體服務數位網路之訊框交換載送服務
A-Civil Engineering & Architecture
CNS 11320    2018 Edition
Method of Test for Abrasion Resistance of Stone Subjected to Foot Traffic
石材腳踏磨損抗力試驗法
C-Electrical Engineering
CNS 9136    2018 Edition
250V Single-Core, Twin-Core, Three-Core EPR Insulated CP Sheathed Metal Netting Covered Cable (250V-SPNC, 250V-DPNC, 250V-TPNC) and PVC Anti-Corrosion Cable (250V-SPNCY, 250V-DPNCY, 250V-TPNCY) for Marine Use
船用250V單心、二心、三心EPR絕緣CP被覆金屬網鎧裝電纜及250V單心、二心、三心EPR絕緣CP被覆金屬網鎧裝PVC防蝕電纜
Z6-Physical Distribution & Packaging
CNS 10634    2018 Edition
Method of test for stitch strength of sewn kraft paper sacks
縫製牛皮紙袋針步強度試驗法
N-Agriculture, Food
CNS 15002    2018 Edition
Method of test for fruit and vegetable juice products - Determination of sugars and sorbitol by HPLC
水果及蔬菜汁飲料檢驗法-糖及糖醇之測定(HPLC法)

Find out:7275Items   |  To Page of: First -Previous-Next -Last  | [113] [114] [115] [116] [117] [118] [119]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.