CNS Standards Solution | HOME | LOGIN | SIGN UP | CONTACT US | 中文版 |
�� ��

Chinese National Standards
中華民國國家標準
- Taiwan 台灣 -
 

"8 " CNS Standards List

| Crimped wire | Varnish Dry | Method test | Sport Drinks | Higher yield | Marine Cast | Rust preventive | IPv6 over |

C-Electrical Engineering
CNS 13198    2017 Edition
Fixed Multilayer Ceramic Chip Capacitors for Use in Electronic Equipment
電子設備用固定多層陶瓷晶片電容器
X-Information & Communication
CNS 15328    2017 Edition
Information technology - Automatic identification and data capture techniques - Radio frequency identification device performance test methods
資訊技術-自動識別與資料擷取技術-無線射頻識別裝置效能測試方法
Z9-General & Miscellaneous
CNS 14368    2017 Edition
Micrographics-Recommendations for the creation of original documents
微縮技術-製作原始文件的建議
Z8-General & Miscellaneous
CNS 12548    2017 Edition
Method of Shear Test for Side Fillet Welded Joint
側面填角熔接接合之剪切試驗法
K-Chemical Industry
CNS 15832-2-1    2017 Edition
Method of test for coating components − Part 2-1: Component analysis in solvent soluble matter − Acid value (Titrimetric method)
塗料成分試驗法-第2-1部:溶劑可溶物中成分分析-酸價(滴定法)
P-Pulp & PaperIndustry
CNS 12986    2017 Edition
Sizes of Untrimmed Paper
裁切前原紙尺度

Translated
G-Ferrous Materials & Metallurgy
CNS 8277    2017 Edition
Rerolled carbon steel
再軋碳鋼鋼料
B-Mechanical Engineering
CNS 12558    2017 Edition
Method of Test for Solar Water Heater System (Automatic Cycle)
自然循環式太陽能熱水系統檢驗法
K-Chemical Industry
CNS 6928    2017 Edition
Method of Test for Scrub Resistance of Interior Latex Flat Wall Paints
室內用乳膠漆耐洗刷性試驗法
B-Mechanical Engineering
CNS 4846    2017 Edition
Hexagon Head Pipe Plugs with Taper Thread
六角頭管塞(具推拔螺紋)
Z2-Industry Safety
CNS 12860    2017 Edition
Handling Standard of Rubber Hose Assembly Use for Liquefied Petroleum Gas
液化石油氣用橡皮管組件之儲藏及使用
C-Electrical Engineering
CNS 8671    2017 Edition
Method of Test for Dry Reed Switches(Contact Stickiness)
乾式簧開關檢驗法(接觸粘著性)
L-Textile Industry
CNS 13982-15    2017 Edition
Methods of test for bulk down and feather − Part 15: Determination of net fill weight
羽絨羽毛試驗法-第15部:裝填淨重測定法
B-Mechanical Engineering
CNS 8194    2017 Edition
Subplate Type Solenoid Operated 4 - Port Valves for Oil - Hydraulic Use
液壓用副板型四通電磁操作閥
B-Mechanical Engineering
CNS 12068    2017 Edition
Support of Die Casting Molds
壓鑄模用支座
B-Mechanical Engineering
CNS 178    2017 Edition
Flat Fitted Keys and Its Seat (for Taper Shaft End)
配合平鍵及槽(用於錐軸梢)
C-Electrical Engineering
CNS 5518    2017 Edition
Non-insulated Crimp-type Sleeves for Copper Conductors
銅線用祼壓接套筒

Translated
L-Textile Industry
CNS 13982-8    2017 Edition
Methods of test for bulk down and feather − Part 8: Determination of fill power with steam conditioning
羽絨羽毛試驗法-第8部:蒸汽處理後蓬鬆度測定法
M-Mining
CNS 7285    2017 Edition
Method for Determination of Gold and Silver in Ores with Tellurium
含碲礦中金及銀定量法
D-Automotive & Aircraft Engineering
CNS 15481-3    2017 Edition
Road vehicles - Environmental conditions and testing for electrical and electronic equipment - Part 3: Mechanical loads
道路車輛-電機電子配備環境條件與試驗-第3部:機械負載
C-Electrical Engineering
CNS 10698    2017 Edition
Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Squelch Blocking, Receiver Attack and Closing Time)
陸上行動通信用25–947MHz調頻/調相接收機檢驗法(靜音截斷、接收機動作及閉合時間)
C-Electrical Engineering
CNS 8791    2017 Edition
Method of Test for Low-Temperature Characteristics of Heat Shrinkable Tubing for Electrical Insulation
電絕緣用熱收縮套管低溫特性試驗法
P-Pulp & PaperIndustry
CNS 14685    2017 Edition
Pulps - Preparation of laboratory sheets for measurement of reflectance
紙漿、紙及紙板表示性能之國際單位
C-Electrical Engineering
CNS 11830    2017 Edition
Measuring Methods for Light Emitting Diodes (for Indication)
發光二極體(指示用)測量法
P-Pulp & PaperIndustry
CNS 2388    2017 Edition
Method of Test for Combustion Rate of Cigarette Paper
捲菸紙燃燒率試驗法

Translated
K-Chemical Industry
CNS 1089    2017 Edition
Method of Test for Polyvinyl Chloride
聚氯乙烯檢驗法
C-Electrical Engineering
CNS 10898    2017 Edition
Flat Quick-Connect Terminals
平板型接頭
N-Agriculture, Food
CNS 2089    2017 Edition
Edible Melon Seed
食用瓜子

Translated
B-Mechanical Engineering
CNS 5284    2017 Edition
Addendum Modification of Spur Gears in the 0.5 System, Introduction
0.5齒制正齒輪之齒廓移位
B-Mechanical Engineering
CNS 10868    2017 Edition
Method of Test for Sewing Performance of Household Zig-zag Lock Stitch Sewing Machines
家庭用錯縱縫縫紉機縫製性能試驗方法

Find out:4917Items   |  To Page of: First -Previous-Next -Last  | [110] [111] [112] [113] [114] [115] [116]

 

| HOME | LOGIN | SIGN UP | CONTACT US | 中文版 | ©  CNS-standards.org Copyright  2001-2025 All Rights Reserved
The authority agency link :
Bureau of Standards, Metrology & Inspection M.O.E.A.
This site is not affiliated with or endorsed by the BSMI or MOEA.