"9 " CNS Standards List |
|
CNS 5967
2017 Edition Bronze Screwed Swing Check Valves (10kgf/c㎡) 青銅螺紋口擺動型止回閥（10 kgf/㎠） |
|
|
|
CNS 98
2017 Edition Accuracy Inspection of Shaping Machines 牛頭刨床精度檢驗 |
Translated |
|
|
CNS 15996
2017 Edition Plastic fuel tanks for passenger cars (replaced by CNS 14579-1) 燃氣用塑膠軟管 |
|
|
|
CNS 13590
2017 Edition Method of Test for Plastic Flammability - Oxygen Index Method 塑膠燃燒性試驗法–氧指數法 |
Translated |
|
|
CNS 3898
2017 Edition Canned abalone mushroom 鮑魚菇罐頭 |
|
|
|
CNS 12295
2017 Edition General Rules for Reliability Assured Power Type Fixed Wire Wound Resistors 可靠度保證功率型線繞固定電阻器總則 |
|
|
|
CNS 295
2017 Edition Methods of Chemical Test for Braze 銲臘化學檢驗法 |
|
|
|
CNS 4790
2017 Edition Glossary of terms used in pulp and paper industry ─ General terms of pulp 紙漿與紙詞彙─紙漿一般名詞 |
|
|
|
CNS 9465
2017 Edition Test Code for Accuracy of Bed Type Vertical Milling Machines 床台型立式銑床精度檢驗標準 |
Translated |
|
|
CNS 9503
2017 Edition Phosphor bronze and nickel silver sheets, plates and strips 磷青銅及鎳銀之板及捲片 |
|
|
|
CNS 10695
2017 Edition Method of Test for Land Mobile Communication FM or PM Receivers, 25-947 MHz (Audio Frequency Response, Harmonic Distortion Factor, Hum and Noise) 陸上行動通信用２５–９４７ＭＨｚ調頻／調相接收機檢驗法（聲頻響應、諧波失真因數、交流聲及雜訊） |
|
|
|
CNS 10993
2017 Edition Methods of Testing Preformed Expansion Joint Fillers for Concrete (Nonextruding and Resilient Types) 混凝土伸縮縫預製填縫物試驗法（凹式） |
|
|
|
CNS 11895
2017 Edition General Rules for Reliability Assured Fixed Mica Capacitors 可靠度保證雲母固定電容器總則 |
|
|
|
CNS 9230
2017 Edition Method of Test for Dry Reed Switches (Contact Life Testing) 乾式簧開關檢驗法（接觸點壽命試驗） |
|
|
|
CNS 11898
2017 Edition Reliability Assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性Ｍ） |
|
|
|
CNS 4949
2017 Edition Tapping Screws, Applications and Core Holes 自攻螺釘，其應用及心孔直徑（薄板用） |
|
|
|
CNS 9697
2017 Edition Brake Pipe Air Strainers for Railway Rolling Stock 鐵路車輛軔管用空氣濾塵器 |
|
|
|
CNS 4429
2017 Edition Hexagon Nuts, Rounded Trapezoidal Thread 凸肩螺帽（公制細螺紋，圓角梯形螺紋） |
|
|
|
CNS 123
2017 Edition Metric Taper for Tools 9-200 (with Flat End) 工具圓錐（公制圓錐９–２００）（有扁頭） |
|
|
|
CNS 10978
2017 Edition Aerosol type mini fire extinguish 噴霧式迷你型滅火器 |
|
|
|
CNS 4309
2017 Edition Conical Spring Washers 圓錐彈簧墊圈 |
|
|
|
CNS 9363
2017 Edition Method of Test for Low Frequency(Below 3 MHz) Electrical Connectors (TP - 1 Acceleration) 頻率３ＭＨｚ以下電連接器檢驗法（加速力ＴＰ–１） |
|
|
|
CNS 12887
2017 Edition Method of Test for Accelerated Aging of Paper and Paperboard - Moist Heat Treatment at 90℃ and 25% R.H. 紙及紙板加速老化試驗法─90℃及25％R.H.濕熱處理 |
Translated |
|
|
CNS 13982-8
2017 Edition Methods of test for bulk down and feather − Part 8: Determination of fill power with steam conditioning 羽絨羽毛試驗法－第8部：蒸汽處理後蓬鬆度測定法 |
|
|
|
CNS 9396
2017 Edition Secondary Aluminium Ingot 再生鋁錠 |
|
|
|
CNS 9790
2017 Edition Opening pressure vessels 壓力容器之孔補強 |
|
|
|
CNS 5509
2017 Edition Rolling Bearings; Bearings with Sphericall Outside Surface and Extended Inner Ring Width, Cast Housings for Insert Bearings 嵌入夾緊滾動軸承用鑄製外殼 |
|
|
|
CNS 3093
2017 Edition Cemented Carbide Dies for Drawing Wires and Rods 超硬合金抽線模 |
|
|
|
CNS 169
2017 Edition Flat Fitting Keys and Sliding Cotter 配合平鍵及滑鍵 |
|
|
|
CNS 12926
2017 Edition 100mm.65mm Stationary Handling Operated Fire Water Monitor １００ｍｍ、６５ｍｍ進出水口固定型操作式消防水瞄 |
|
| Find out:5209Items | To Page of: First -Previous-Next -Last | [107] [108] [109] [110] [111] [112] [113] |
