"c " CNS Standards List |
|
CNS 20005
2020 Edition Information technology − Sensor networks − Services and interfaces supporting collaborative information processing in intelligent sensor networks 資訊技術－感測器網路－智慧感測器網路中支援協作資訊處理之服務及介面 |
|
|
|
CNS 5270-5
2020 Edition Graphical Symbols for Fluid Power Diagrams-Pressure Control Valve 液壓、氣壓圖形符號–壓力控制閥 |
|
|
|
CNS 15775
2020 Edition Acoustics − Specification of test tracks for measuring noise emitted by road vehicles and their tyres 聲學－供車輛及其輪胎噪音量測用試驗道規格 |
|
|
|
CNS 1870
2020 Edition Picks, Two Taper Ends 化學試藥（苦味酸） |
|
|
|
CNS 1880
2020 Edition Potassium Bromide (Reagent) 化學試藥（碳酸鉀，無水） |
|
|
|
CNS 13169
2020 Edition Safety Standards for construction of Veneer Lathes 單板旋切機之構造安全基準 |
|
|
|
CNS 14930
2020 Edition Doors, entrance platforms, windows, steps, handles and handrails of coaches and luggage vans 軌道客車及行李車之車門、出入台、車窗、台階、握桿及扶手 |
|
|
|
CNS 13167
2020 Edition Safety Standards for construction of Spindle Shapers 立軸機之構造安全基準 |
|
|
|
CNS 11424
2020 Edition Method of Test for Setting Time of Refractory Mortar 耐火墁料凝結時間試驗法 |
|
|
|
CNS 1706
2020 Edition Disodium Dihydrogen Ethylenediamine Tetraacetate Dihydrate 化學試藥（伸乙二胺四乙酸二氫二鈉二水合物） |
|
|
|
CNS 5079
2020 Edition Gypsum casting and Molding Plaster 鑄用及模型用熟石膏 |
|
|
|
CNS 12969
2020 Edition Porcelain Guide 瓷質金斗與骨灰罎 |
|
|
|
CNS 392
2020 Edition Thin Bearing Sleeve 薄軸承襯 |
|
|
|
CNS 15345-1
2020 Edition Safety of machinery - Reduction of risk to health from hazardous substances emitted by machinery - Part 1: Principles and specification for machinery manufacturers 機械安全－降低由機械釋放有害性物質對健康造成之風險－第１部：對機械製造商之原則及規範 |
|
|
|
CNS 11423
2020 Edition Method of Test for Grain Size of Refractory Mortar 耐火墁料細度試驗法 |
|
|
|
CNS 9350
2020 Edition Bushes for Plain Bearings with Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 80000-9
2020 Edition Quantities and units – Part 9: Physical chemistry and molecular physics 量及單位－第9部：物理化學與分子物理學 |
|
|
|
CNS 14678
2020 Edition coaches-windows made from glass 客車廂之玻璃窗 |
|
|
|
CNS 8930
2020 Edition Switchgears, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 11081
2020 Edition Method for calculating Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 4539
2020 Edition Terms relating to the manufacture of fasteners 結件詞彙（製造方法） |
|
|
|
CNS 16129-2
2020 Edition Railway applications − Welding of railway vehicles and components − Part 2: Quality requirements and certification of welding manufacturer 鐵路應用－鐵路車輛及其零組件之銲接－第2部：銲接製造廠商品質要求及驗證 |
|
|
|
CNS 121
2020 Edition collar (Using Heavy Duty Set Screws) 頸圈（用螺絲銷、重型） |
|
|
|
CNS 2512
2020 Edition Determination of paper sizing − Stöckigt method 紙之上膠度試驗法－史托克法 |
|
|
|
CNS 7029
2020 Edition Shape, Dimensions and Travel Angles of Drawbar Eyes for Full Trailers 全拖車用拖桿環首之形狀、尺度及活動範圍 |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 12843
2020 Edition chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [101] [102] [103] [104] [105] [106] [107] |
