"5 " CNS Standards List |
|
CNS 9599
2018 Edition Marine Floodlighting Projectors 船用投射燈 |
|
|
|
CNS 15612
2018 Edition Plastics − Determination of the melt mass-flow rate (MFR) and melt volume-flow rate (MVR) of thermoplastics − Part 1: Standard method 塑膠－吸水率測定法 |
|
|
|
CNS 5461
2018 Edition Refined benzene-535 精製苯-535 |
|
|
|
CNS 15703-2
2018 Edition Tool shanks with 7/24 taper for automatic tool changers – Part 2: Dimensions and designation of shanks of forms J, JD and JF 自動換刀器用7/24 錐度刀柄－第2 部：刀柄型式J、JD 及JF 之尺度及標示 |
|
|
|
CNS 14545-6
2018 Edition Fire hazard testing-Part 2:Test methods-Section 1/sheet 2:Glow-wire flammability test on materials 火災危險性試驗－第２部：試驗方法－第１章／第２單元：材料可燃性之熾熱線試驗 |
|
|
|
CNS 14952-3-1
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials - Part 3: Instructions for calculating thermal endurance characteristics - section 1: calculations using mean values of normally distributed complete data 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第１章：利用常態分配完整資料的平均值進行計算 |
|
|
|
CNS 13853-2
2018 Edition Information technology - Computer graphics - Metafile for the storage and transfer of picture description information - Part 2:Character encoding 資訊技術–電腦圖形–儲存與轉送圖象描述資訊的元檔–第２部：字元編碼 |
|
|
|
CNS 13283-5
2018 Edition Electronic data interchange for administration, commerce and transport(EDIFACT)－Application level syntax rules (Syntax version number：4) Part 5：Security rules for batch EDI (authenticity, integrity and non-repudiation of origin) 行政管理、商務與運輸用電子資料交換(EDIFACT)－應用層語法規則(第4版語法)－第5部：針對批次式EDI的安全規則(鑑別性、完整性、來源不可否認性) |
|
|
|
CNS 3685
2018 Edition Method of test for thickness and apparent density of paper and board 紙及紙板厚度及密度試驗法 |
Translated |
|
|
CNS 15568
2018 Edition Protecting Equipment and Distribution of Three-Phase 220 V Motors for General Use 電擊防護－裝設及設備之一般觀念 |
|
|
|
CNS 14325
2018 Edition Broadband integrated services digital network (B-ISDN)-Digital subscriber signalling system no.2 (DSS 2)-Additional traffic parameters 寬頻整體服務數位網路－第二號數位用戶信號系統－附加訊務參數 |
|
|
|
CNS 9488
2018 Edition Marine Bronze 5 kgf / ㎠ Screw-down Check Angle Valves (Union Bonnet Type) 船用青銅管套帽型螺桿止回角閥（5 kgf/㎠） |
|
|
|
CNS 15590-7
2018 Edition Mechanical properties of fasteners – Part 7: Torsional test and minimum torques for bolts and screws with nominal diameters 1 mm to 10 mm 結件之機械性質－第7部：標稱直徑1 mm至10 mm螺栓與螺釘之扭力試驗及最小扭矩 |
|
|
|
CNS 9153
2018 Edition 660V, Twin-Core, Three-Core EPR Insulated PVC Sheathed Metal Netting Covered Cable and 660V Twin-Core, Three-Core EPR Insulated PVC Sheathed Metal Netting Covered PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及６６０Ｖ二心、三心ＥＰＲ絕緣ＰＶＣ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 9154
2018 Edition 660V, Twin-Core, Thre-Core EPR Insulated CP Sheathed Metal Netting Covered Cable and 660V Twin-Core, Three-Core EPR Insulated CP Sheathed Metal Netting Cover PVC Anti-Corrosion Cable for Marine Use 船用６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝電纜（附各心線個別遮蔽）及６６０Ｖ二心、三心ＥＰＲ絕緣ＣＰ被覆金屬網鎧裝ＰＶＣ防蝕電纜（附各心線個別遮蔽） |
|
|
|
CNS 9492
2018 Edition Marine Bronze 5 kgf/㎠ Lift Check Angle Valves (Union Bonnet Type) 船用青銅管套帽型升程止回角閥（5 kgf/㎠） |
|
|
|
CNS 14952-3-2
2018 Edition Guide for the determination of thermal endurance properties of electrical insulating materials – Part 3: Instructions for calculating thermal endurance characteristics – section 2: the calculation for incomplete data – verification for test result from gr 電氣絕緣材料之耐熱性測定指引－第３部：耐熱特性計算之說明－第２章：不完整資料的計算－以包含中間時間到終止點之等量試驗群組驗證試驗結果 |
|
|
|
CNS 15398
2018 Edition Green coffee − Determination of proportion of insect-damaged beans 咖啡生豆－蟲害豆含量測定法 |
|
|
|
CNS 15395
2018 Edition Green coffee − Determination of loss in mass at 105 ℃ 咖啡生豆－於105 ℃之質量損失測定法 |
|
|
|
CNS 13919
2018 Edition Equipment to perform in-service monitoring on 1544 Kbps signals 服務狀態中監視 1544 Kbps 信號之設備 |
|
|
|
CNS 14151
2018 Edition Line transmission of non-telephone signals - Procedures for establishing communication between threeor more audiovisual terminals using digital channels up to 2Mbit/s 非電話信號之線傳輸–使用可達２Ｍｂｐｓ數位通道建立三部或以上視聽終端機間通訊之程序 |
|
|
|
CNS 15660-7
2018 Edition Test conditions for numerically controlled turning machines and turning centres − Part 7: Evaluation of contouring performance in the coordinate planes 數值控制車床及車削中心機之試驗條件－第7 部：座標平面上循跡性能評估 |
|
|
|
CNS 15710-3
2018 Edition Effects of current on human beings and livestock – Part 3: Effects of currents passing through the body of livestock 電流在人體及家畜上之效應－第3 部：電流通過家畜軀體之效應 |
|
|
|
CNS 15832-2-4
2018 Edition Method of test for coating components − Part 2-4: Component analysis in solvent soluble matter − Alkyd resin 塗料成分試驗法－第2-4部：溶劑可溶物中成分分析－醇酸樹脂 |
|
|
|
CNS 8075
2018 Edition Mtheod of Test for Building Components (Concrete Panels for Roofs) 建築用組件（混凝土屋頂嵌板）檢驗法 |
|
|
|
CNS 14356-1
2018 Edition Information Technology--Open Document Architecture(ODA)and Interchange Format:Document Structure 資訊技術－開放文件架構與交換格式：文件結構 |
|
|
|
CNS 15002
2018 Edition Method of test for fruit and vegetable juice products - Determination of sugars and sorbitol by HPLC 水果及蔬菜汁飲料檢驗法－糖及糖醇之測定（ＨＰＬＣ法） |
|
|
|
CNS 15676-2
2018 Edition Interior air of road vehicles − Part 2: Screening method for the determination of the emissions of volatile organic compounds from vehicle interior parts and materials − Bag method 道路車輛內部空氣－第2 部：車輛內部零件與材料之揮發性有機化合物逸散量篩檢測定法－採樣袋法 |
|
|
|
CNS 6275
2018 Edition Purity of Acrylate Esters by Gas Chromatography 彎盆 |
|
|
|
CNS 13715
2018 Edition Message Transfer Part (MTP) Signalling Preformance of Signalling System No.7 第七號信號系統訊息轉送部信號效能 |
|
| Find out:6646Items | To Page of: First -Previous-Next -Last | [101] [102] [103] [104] [105] [106] [107] |
