", " CNS Standards List |
|
CNS 121
2020 Edition Collar (Using Heavy Duty Set Screws) 頸圈（用螺絲銷、重型） |
|
|
|
CNS 9409
2020 Edition Chemical Reagent (Triphenylchloromethane) 化學試藥（三苯氯甲烷） |
|
|
|
CNS 1887
2020 Edition Potassium Fluoride(Reagent) 六氰鐵（Ⅲ）酸鉀（試藥） |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 5786
2020 Edition Electric Windshield Washers for Automobiles 汽車擋風玻璃電動噴洗器 |
|
|
|
CNS 30128
2020 Edition Information technology − Sensor networks − Generic sensor network application interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 13167
2020 Edition Safety Standards for Construction of Spindle Shapers 立軸機之構造安全基準 |
|
|
|
CNS 4797-6
2020 Edition Safety of toys − Part 6: Organic chemical compounds − Requirements 玩具安全－第6部：有機化合物－要求事項 |
|
|
|
CNS 3325
2020 Edition Standard Classification of Castable Refractories 可鑄耐火物分級標準 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 9746
2020 Edition Method of Test for Potential Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 1867
2020 Edition Phosphorus Trichoride 化學試藥（三氯化磷） |
|
|
|
CNS 13169
2020 Edition Safety Standards for Construction of Veneer Lathes 單板旋切機之構造安全基準 |
|
|
|
CNS 1870
2020 Edition Picks, Two Taper Ends 化學試藥（苦味酸） |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 1559
2020 Edition Diammonium hydrogenphosphate (reagent) 化學試藥（磷酸氫二銨） |
|
|
|
CNS 14104-4
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 3: Method of describing upper limb amputation stumps 義肢學與矯具學－肢體缺陷－第４部：導致截肢原因之描述 |
|
|
|
CNS 1947
2020 Edition Sodium Bisulfate, Fused 化學試藥（融熔硫酸氫鈉） |
|
|
|
CNS 330
2020 Edition Hand Wheels of Low Heat Insulation Materials 手輪（以低導熱材料製成） |
|
|
|
CNS 5270-1
2020 Edition Graphical Symbols for Fluid Power Dizgrams-Line and Connection 液壓、氣壓圖形符號–管路及連接 |
|
|
|
CNS 15374
2020 Edition Liquefied petroleum gases - Determination of dissolved residues (High-temperature gas chromatographic method) 液化石油氣－可溶殘餘物測定法（高溫氣相層析法） |
|
|
|
CNS 16145-2
2020 Edition Ceramic tiles − Grouts and adhesives − Part 2: Test methods for adhesives 陶瓷面磚－填縫劑與接著劑－第2部：接著劑試驗法 |
|
|
|
CNS 3333
2020 Edition Zinc alloy ingots intended for castings 鑄造用鋅合金錠 |
|
|
|
CNS 16142
2020 Edition Balancing of rotating tools and tool systems 旋轉刀具及刀具系統之平衡調校 |
|
|
|
CNS 11424
2020 Edition Method of Test for Setting Time of Refractory Mortar 耐火墁料凝結時間試驗法 |
|
|
|
CNS 15333
2020 Edition Quality management - Guidelines for training 品質管理－訓練指導綱要 |
|
|
|
CNS 8930
2020 Edition Switchgears, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 11277
2020 Edition Hardening by Induction Heating and Tempering of Iron and Steel 鐵及鋼之高週波淬火回火熱處理 |
|
|
|
CNS 15832-4-2
2020 Edition Method of test for paint components − Part 4-2: Analysis for components emitted from film − Volatile organic compounds 塗料成分試驗法－第4-2 部：塗膜釋出成分分析－揮發性有機化合物(VOC) |
|
| Find out:16181Items | To Page of: First -Previous-Next -Last | [101] [102] [103] [104] [105] [106] [107] |
