"And " CNS Standards List |
|
CNS 5508
2017 Edition Rolling Bearings; Bearings with Spherical Outside Surface And Extended Inner Ring Width, Steel Pressed Housings for Insert Bearings 嵌入夾緊滾動軸承用壓製外殼 |
|
|
|
CNS 13788
2017 Edition Methods of Test for Water Vapor Transmission Rate of Plastic Films And Sheets (Instrument Method) 塑膠薄膜及薄片透濕度試驗法（儀器法） |
Translated |
|
|
CNS 4790-6
2017 Edition Glossary of terms used in pulp And paper industry ─ Terms for types and properties of paper and paperboard ─ Converted products 紙漿與紙詞彙─紙與紙板種類名詞 |
|
|
|
CNS 8876
2017 Edition Fire manual station And its fire alarm bell indication lamp 火警發信機及其火警警鈴、標示燈 |
Translated |
|
|
CNS 4069
2017 Edition Pneumatic fluid power − General rules And safety requirements for systems and their components 氣動輪磨機 |
Translated |
|
|
CNS 13192
2017 Edition Test Methods for Performance And Accuracy of Band Saw Stretchers 帶鋸片伸整機之性能試驗及精度檢驗法 |
|
|
|
CNS 14466-3
2017 Edition Audio-visual, video And television equipment and systems - Part3: Connectors for the interconnection of equipment in audio-visual systems 視聽．影像及電視設備與系統-第３部：視聽系統內設備互連用連接器 |
|
|
|
CNS 12844
2017 Edition Method of Test for Chlorosulfonated Polyethylene Rubber Supported Geomembrane for LAndfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布檢驗法 |
Translated |
|
|
CNS 527
2017 Edition Inspection Plug Gauge for Whitworth Thread Ring Gauge (Go End Limit for Fine, Medium And Coarse Fits) 韋氏螺紋樣圈之量柱及損磨量柱（通過端，精配，中配及粗配） |
|
|
|
CNS 11446-1
2017 Edition Method of measurement on receives for television broadcast transmission - Part 1: General considerations - Measurements at radio And video frequencies 電視廣播傳輸接收機之量測方法-第一部:概論-射頻及視頻之量測 |
|
|
|
CNS 9504
2017 Edition Methods for estimating average grain size of wrought copper And copper alloys 銅及銅合金展伸材料之晶粒尺度測定法 |
|
|
|
CNS 7145
2017 Edition High Tensile Strength Carbon Steel Castings And Low Alloy Steel Castings for Structural Purposes 結構用高強度碳鋼及低合金鋼鑄鋼件 |
|
|
|
CNS 3722
2017 Edition Method of test for milk And milk products - Determination of ash in edible cheese 乳品檢驗法－食用乾酪灰分之測定 |
|
|
|
CNS 10442
2017 Edition Copper And copper alloy rods and bars 銅及銅合金棒 |
|
|
|
CNS 11444
2017 Edition Method of Test for Watt-Hour, Var-Hour And Maximum Demand indicators for Telemetering 瓦時，乏時及電力最大需量表示裝置（分離型）試驗法 |
|
|
|
CNS 4241
2017 Edition Method of Test for Electroplated Coating of Bolts, Screws And Nuts 螺栓、螺釘、螺帽電鍍層之檢驗法 |
|
|
|
CNS 15520
2017 Edition Push And Pull Drain Trap (P Type) 建築物室內用補平塗材 |
|
|
|
CNS 14384-1
2017 Edition Protective gloves − General requirements And test methods 化學藥品及微生物防護手套－用語及性能要求 |
|
|
|
CNS 11093
2017 Edition Junction Box for Indoor Wiring (for Polyvinyl-Chloride Insulated And Sheated Cables: VVF) 屋內配線用接線盒〔平型聚氯乙烯絕緣聚氯乙烯被覆電纜（ＶＶＦ用）〕 |
|
|
|
CNS 13747
2017 Edition Method of Test for Unplasticized Polyvinyl Chloride Pipes with Polyethylene Lining for Wastewater And General Uses 污水及一般用內襯聚乙烯之聚氯乙烯塑膠硬質管檢驗法 |
Translated |
|
|
CNS 4369
2017 Edition Round Thread with Clearance And Flat Flank with Pitch 7 mm; Nominal Sizes 圓螺紋（具有間隙、淺螺腹，螺距為７ｍｍ之標稱尺寸） |
|
|
|
CNS 14782
2017 Edition Manipulating industrial robots —Test equipment And metrology methods of operation for robot performance evaluation 工業用機器人性能評估作業之測試儀器與量測方法 |
|
|
|
CNS 9621-3
2017 Edition Rubber hoses for liquefied petroleum gases (LPGs) - Part 3: Dispensing hoses And hose assemblies 液化石油氣用橡膠管(LPG橡膠管)－第3部：加氣用管及管組合件 |
|
|
|
CNS 9267
2017 Edition Method of mass calculation for stainless steel plates And sheets,and heat-resisting steel plates and sheets 不銹鋼及耐熱鋼鋼板及鋼片質量計算法 |
|
|
|
CNS 14636
2017 Edition Determination of accuracy And repeatability of positioning of numerically controlled machine tools 數值控制工具機定位精度暨重現性檢驗通則 |
|
|
|
CNS 12663
2017 Edition Method of Test for Radiographic And Classification of Radiographs for Titanium Welds 鈦熔接縫放射線透射試驗法及透射照片之等級分類 |
|
|
|
CNS 11708
2017 Edition Method of Test for LAnd Mobile Communication FM or PM Transmitters, 25-470 MHz 陸上行動通信用２５–４７０ＭＨｚ調頻／調相發射機檢驗法 |
|
|
|
CNS 4321
2017 Edition Hexagon Bolts with Approximately to Head, Finished And Semi-Finished, Metric Fine Thread 六角頭全螺紋螺栓（精製及半精製，公制細螺紋） |
|
|
|
CNS 4259
2017 Edition Accuracy Inspection of Knee Type Horizontal Milling Machines And Universal Milling Machines 膝型臥式銑床及萬能銑床精度檢驗標準 |
Translated |
|
|
CNS 11154
2017 Edition Grease Guns-Rush Type HAnd Guns 手用衝壓式黃油槍 |
|
| Find out:4887Items | To Page of: First -Previous-Next -Last | [100] [101] [102] [103] [104] [105] [106] |
