"as " CNS Standards List |
|
CNS 12296
1988 Edition Reliability assured Power Type Fixed Wire Wound Resistors (S) (Established Failure Rate) 可靠度保證功率型線繞固定電阻器（特性Ｓ）（故障率設定） |
Translated |
|
|
CNS 12293
1988 Edition Reliability assured Fixed Carbon Composition Resistors (From 1, Grade X) 可靠度保證混合碳固定電阻器(方式1之等級X) |
Translated |
|
|
CNS 12294
1988 Edition Reliability assured FIxed Carbon Composition Resistors (Form 2,Gradex) 可靠度保證混合碳固定電阻器(方式2之等級X) |
Translated |
|
|
CNS 12295
1988 Edition General Rules for Reliability assured Power Type Fixed Wire Wound Resistors 可靠度保證功率型線繞固定電阻器總則 |
|
|
|
CNS 12355
1988 Edition Contrast of MCM Gage to Diameter and Section Area 美規絞線與公制直徑及有效截面積對照表 |
|
|
|
CNS 10926
1987 Edition Method of Test for Fiber Optic Devices (FOTP-27 Measuring Outside (Uncoated) Diameter of Optical Fibers) 光纖裝置檢驗法（無外被光纖外徑測量法FOTP-27） |
|
|
|
CNS 10927
1987 Edition Method of Test for Fiber Optic Devices (FOTP-28 Measuring Failure Point of Optical Waveguide Fiber) 光纖裝置檢驗法（光纖抗強拉度測量法FOTP-28） |
|
|
|
CNS 5535
1987 Edition Small Switch for Single-phase Motors 單相電動機用小型開關 |
Translated |
|
|
CNS 12072
1987 Edition Locating Pin of Die Casting Molds 壓鑄模用定位銷 |
|
|
|
CNS 11939
1987 Edition Setting Plugs of Molds for Plastics 塑膠型模用定位塞 |
|
|
|
CNS 11901
1987 Edition Dimensions of Racks and Unit Chassis of Electronic Equipment for General Use 一般電子設備用機架及單體機座之尺度 |
|
|
|
CNS 11907
1987 Edition Method of Test for Fiber Optic Devices (FOTP-99 Gas Flame Test for Special Purpose Fiber Optic Cable) 光纖裝置檢驗法（特種用途光纜之火焰試驗FOTP-99） |
|
|
|
CNS 11931
1987 Edition Ejector Sleeves of Molds for Plastics 塑膠型模用頂出套筒 |
|
|
|
CNS 11932
1987 Edition Angle Pins of Molds for Plastics 塑膠型模用角銷 |
|
|
|
CNS 8229
1987 Edition Method of Test For Dry Reed Switches (Operate, Bounce, Release and Transfer (SPDT) Time) 乾式簧開關檢驗法（動作、彈跳、復原與轉接時間） |
|
|
|
CNS 11933
1987 Edition Ejector Guide Pins of Molds for Plastics 塑膠型模用頂出導銷 |
|
|
|
CNS 8225
1987 Edition Method of Test for Dry Reed Switches (Quality Control and Quality assurance Provisions) 乾式簧開關檢驗法（品質管制與品質保證規定） |
|
|
|
CNS 12080
1987 Edition Glossary of Terms Used in Electronic Measuring Apparatus 電子測定器詞彙 |
|
|
|
CNS 11934
1987 Edition Stop Bolts of Molds for plastics 塑膠型模用止動螺栓 |
|
|
|
CNS 11935
1987 Edition Supporter of Molds for Plastics 塑膠型模用支持座 |
|
|
|
CNS 11936
1987 Edition Stop Pins of Molds for Plastics 塑膠型模用止銷 |
|
|
|
CNS 11898
1987 Edition Reliability assured Plastic Film Capacitors (Characteristic M) 可靠度保證塑膠膜電容器（特性M） |
|
|
|
CNS 11938
1987 Edition Sprue Puller of Molds for Plastics 塑膠型模用澆口拉料銷 |
|
|
|
CNS 712
1987 Edition Brass Screwed Globe Valves (10 kgf/㎠) 黃銅螺紋口球型閥(10 kgf/cm2) |
Translated |
|
|
CNS 11993
1987 Edition Method of Test for Fiber Optic Devices (FOTP-50 Light-Launch Conditions for Long Length Graded-Index Optical Fiber Spectral Attenuation Measurement) 光纖裝置檢驗法（長距離斜射率光纖光譜衰減測量之光投射條件FOTP-50） |
|
|
|
CNS 12068
1987 Edition Support of Die Casting Molds 壓鑄模用支座 |
|
|
|
CNS 12069
1987 Edition Ejector Rod of Die Casting Molds 壓鑄模用頂出桿 |
|
|
|
CNS 12071
1987 Edition Angle Pin of Die Casting Molds 壓鑄模用斜角撐銷 |
|
|
|
CNS 12074
1987 Edition Flash Cavity of Hot Forging Closed Die 熱鍛閉合模之餘料穴 |
|
|
|
CNS 8871
1987 Edition Dental Plaster 牙科用普通石膏 |
|
| Find out:3287Items | To Page of: First -Previous-Next -Last | [99] [100] [101] [102] [103] [104] [105] |
