"a " CNS Standards List |
|
CNS 5079
2020 Edition Gypsum Casting and Molding Plaster 鑄用及模型用熟石膏 |
|
|
|
CNS 16129-2
2020 Edition Railway applications − Welding of railway vehicles and components − Part 2: Quality requirements and certification of welding manufacturer 鐵路應用－鐵路車輛及其零組件之銲接－第2部：銲接製造廠商品質要求及驗證 |
|
|
|
CNS 392
2020 Edition Thin Bearing Sleeve 薄軸承襯 |
|
|
|
CNS 121
2020 Edition Collar (Using Heavy Duty Set Screws) 頸圈（用螺絲銷、重型） |
|
|
|
CNS 12969
2020 Edition Porcelain Guide 瓷質金斗與骨灰罎 |
|
|
|
CNS 3325
2020 Edition Standard Classification of Castable Refractories 可鑄耐火物分級標準 |
|
|
|
CNS 12843
2020 Edition Chlorosulfonated Polyethylene Rubber Supported Geomembrane for Landfill 垃圾掩埋場用氯磺化聚乙烯夾網橡膠不透水布 |
Translated |
|
|
CNS 9350
2020 Edition Bushes for Plain Bearings with Lubrication Holes and Grooves 滑動軸承軸襯–有潤滑孔及潤滑槽 |
|
|
|
CNS 61439-4
2020 Edition Low-voltage switchgear and controlgear assemblies − Part 4: Particular requirements for assemblies for construction sites (ACS) 低電壓開關裝置及控制裝置組裝品－第4部：建築工地用組裝品(ACS)之個別要求 |
|
|
|
CNS 4539
2020 Edition Terms relating to the manufacture of fasteners 結件詞彙（製造方法） |
|
|
|
CNS 1880
2020 Edition Potassium Bromide (Reagent) 化學試藥（碳酸鉀，無水） |
|
|
|
CNS 11423
2020 Edition Method of Test for Grain Size of Refractory Mortar 耐火墁料細度試驗法 |
|
|
|
CNS 15775
2020 Edition acoustics − Specification of test tracks for measuring noise emitted by road vehicles and their tyres 聲學－供車輛及其輪胎噪音量測用試驗道規格 |
|
|
|
CNS 11081
2020 Edition Method for Calculating Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 14315
2020 Edition Methods of test for bending fatigue of fine ceramics at room temperature 精密陶瓷室溫彎曲疲勞試驗法 |
|
|
|
CNS 9341
2020 Edition Oil Seals 油封 |
|
|
|
CNS 14678
2020 Edition Coaches-windows made from glass 客車廂之玻璃窗 |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 8930
2020 Edition Switchgears, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 8408-2
2020 Edition accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 14503-1
2020 Edition Evaluation methods for pitting corrosion of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Chart method 鋁及鋁合金之陽極氧化膜孔蝕評定法－第１部：圖示法 |
|
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 15820-2
2020 Edition Electric motorcycles − Safety specifications − Part 2: Protection against hydrogen hazards for motorcycles fuelled with compressed hydrogen 電動機車－安全規範－第2 部：防止氫氣危害 |
|
|
|
CNS 61427-1
2020 Edition Secondary cells and batteries for renewable energy storage − General requirements and methods of test − Part 1: Photovoltaic off-grid application 再生能源儲能用二次單電池及電池組－一般要求及試驗法－第1部：太陽光電離網應用 |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 9746
2020 Edition Method of Test for Potential Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 8988
2020 Edition Chemical Reagent(Dry Loss Determination) 化學試藥（乾失量測定） |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 519
2020 Edition Limit of Whitworth Threads (Fine Fit) 韋氏螺紋限界尺寸（精配） |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [96] [97] [98] [99] [100] [101] [102] |
