"G " CNS Standards List |
|
CNS 14934-5
2019 Edition ElectromaGnetic compatibility (EMC) - Limits - Part 5: Limitation of voltage fluctuations and flicker in low-voltage power supply systems for equipment with rated current greater than 16A 電磁相容－限制值－第5部：額定電流大於16 A之設備於低電壓電源系統中電壓變動及閃爍之限制值 |
|
|
|
CNS 13181-2
2019 Edition The Method of Test of Presure ReGulator and Vaporizers for LGP Automobile Fuel Systems 液化石油氣汽車燃氣系統–壓力調整器與氣化器檢驗法 |
Translated |
|
|
CNS 15779
2019 Edition Information technoloGy − Automatic identification and data capture techniques − GS1 DataBar bar code symbology specification 資訊技術－自動識別與資料擷取技術－GS1 DataBar 條碼符號表示法 |
|
|
|
CNS 8110
2019 Edition Marine ForGed Steel Globe Valves for Compressed Air 船用鍛鋼壓縮空氣球形閥 |
|
|
|
CNS 14498-2
2019 Edition Road vehicles - Electrical disturbances from conduction and couplinG - Part 2: Electrical transient conduction along supply lines only 道路車輛－經由傳導及耦合之電擾動－第２部：僅由電源線傳導之電暫態 |
|
|
|
CNS 14128
2019 Edition Method of impact test for instrument panel of passenGer cars 小客車用儀表板衝擊試驗法 |
|
|
|
CNS 6959
2019 Edition Acid and Heat ResistinG Bricks for Chemical Industry 化學工業用耐酸耐熱磚 |
|
|
|
CNS 15030-17
2019 Edition Classification and labellinG of chemicals - Acute toxicity 化學品分類及標示－急毒性物質 |
Translated |
|
|
CNS 7529
2019 Edition Method for samplinG of abrasive grains 磨料採樣法 |
|
|
|
CNS 14899
2019 Edition Polyethylene Insulated Self-SupportinG Drop Wires 聚乙烯大口徑異型管壁污水與排水管 |
|
|
|
CNS 20349-1
2019 Edition Personal protective equipment − Footwear protectinG against risks in foundries and welding − Part 1: Requirements and test methods for protection against risks in foundries 個人防護具－防止鑄造及熔接中風險之鞋類－第1部：防護鑄造中風險之要求事項及試驗方法 |
|
|
|
CNS 14205
2019 Edition General aspects of digital transmission systems; terminal equipments - coding of speech at 16 kbps using low-delay code excited linear prediction 數位傳輸系統之一般觀念終端設備–使用低延遲碼激發線性預測之 16 kbps 語音編碼 |
|
|
|
CNS 14545-5
2019 Edition Fire hazard testinG-Part 2:Test methods-Section 1/sheet 1:Glow-wire end-product test and guidance 火災危險性試驗－第２部：試驗方法－第１章／第１單元：完成品之熾熱線試驗及指引 |
|
|
|
CNS 15200-1-6
2019 Edition TestinG methods for paints - Part 1-6: General rule - Temperatures and humidities for conditioning and testing 塗料一般試驗方法－第１－６部：通則－調節與試驗之溫度及濕度 |
|
|
|
CNS 12770
2019 Edition Method of Test for Buoyant Smoke SiGnal for Marine Use 船用浮煙信號設備檢驗法 |
|
|
|
CNS 15449-2-101
2019 Edition Safe requirements for electrical for measurement, control and laboratory use ? Part 2-101: Particular requirements for in vitro diaGnostic (IVD) medical equipment 量測、控制及實驗室使用電氣設備安全規定－第2-101 部:體外診斷(IVD)醫用設備之個別規定 |
|
|
|
CNS 5564
2019 Edition Rated Output and Its Test Methods for Automobile Generators 汽車用發電機之額定輸出及試驗法 |
|
|
|
CNS 4273
2019 Edition Steel plates,sheets and strips for Gas cylinders 高壓瓦斯容器用鋼板、鋼片及鋼帶 |
|
|
|
CNS 12456
2019 Edition Corrosion Inhibitor for ReinforcinG Steel in Concrete 鋼筋混凝土用防銹劑 |
|
|
|
CNS 29100-1
2019 Edition Information technoloGy − Security techniques − Specification for a personal information management system 資訊技術－安全技術－個資管理系統要求事項 |
|
|
|
CNS 14545-1
2019 Edition Fire hazard testinG-part 1:Guidance for assessing fire hazard of electrotechnical products(general guidance) 火災危險性試驗－第１部：評估電氣產品火災危險性的指引（通則） |
|
|
|
CNS 15200-1-5
2019 Edition TestinG methods for paints - Part 1-5 : General rule - Coating of test panel (brush application) 塗料一般試驗方法－第１－５部：通則－試驗板之塗裝（刷塗） |
|
|
|
CNS 8574
2019 Edition Glossary of Terms Relating to Electric Equipment for Automobiles (Windshield Wiper System) 汽車用電器零件詞彙（雨刷系統） |
|
|
|
CNS 15176-26-1
2019 Edition Wind turbines − Part 26-1: Time-based availability for wind turbine Generating systems 風力機－第26-1 部：風力發電機系統以時間為基礎之可利用率 |
|
|
|
CNS 15767-2-5
2019 Edition PluG (Working Pressure Less Than 16 kg/㎠) 家用和類似用途插頭及插座－第2-5部：轉接器之特定要求 |
|
|
|
CNS 13921
2019 Edition Method of atomic emission spectrophotoelectric analysis for die castinG zinc alloy 壓鑄鋅合金之光電式發光光譜分析法 |
|
|
|
CNS 12493
2019 Edition HiGh Density Polyethylene Geomembrane for Sanitary Landfill 垃圾掩埋場用高密度聚乙烯不透水布 |
Translated |
|
|
CNS 7892
2019 Edition Speed indicatinG devices for automobiles 汽車用速率指示裝置 |
|
|
|
CNS 8573
2019 Edition Glossary of Terms Relating to Electric Equipment for Automobiles (Lamp System) 汽車用電器零件詞彙（燈系統） |
|
|
|
CNS 16093-1
2019 Edition WeldinG and allied processes − Types of joint preparation − Part 1: Manual metal arc welding, gas-shielded metal arc welding, gas welding, TIG welding and beam welding of steels 銲接及其相關製程－接頭準備型式－第1部：鋼的被覆銲條電弧銲接、氣體遮護金屬電弧銲接、氣銲、惰氣遮護金屬電弧銲接及能束銲接 |
|
| Find out:10068Items | To Page of: First -Previous-Next -Last | [96] [97] [98] [99] [100] [101] [102] |
