"a, " CNS Standards List |
|
CNS 6903
2020 Edition Cable Terminals for Automobiles (Type LB) 汽車用電線端子（橫接環眼型） |
|
|
|
CNS 2009
2020 Edition Sulfuric Acid, Fuming 化學試藥（發煙硫酸） |
|
|
|
CNS 17296-4
2020 Edition Additive manufacturing − General principles − Part 4: Overview of data processing 積層製造－通則－第4部：資料處理之概述 |
|
|
|
CNS 30128
2020 Edition Information technology − Sensor networks − Generic sensor network application interface 資訊技術－感測器網路－ 通用感測器網路應用介面 |
|
|
|
CNS 4354
2020 Edition Finishes and tolerances for product grade of screws and nuts 螺釘與螺帽之加工精度及公差（特精級） |
|
|
|
CNS 15804
2020 Edition Oil of cassia, Chinese type − Determination of trans-cinnamaldehyde content − Gas chromatographic method on capillary columns 肉桂油(中國型)－反桂皮醛含量測定法－毛細管柱氣相層析法 |
|
|
|
CNS 5561-2
2020 Edition High Tension Cable Connection for Ignition Coils and Distributors for Automobiles 汽車用點火線圈及分電盤用高壓接線端子 |
|
|
|
CNS 7029
2020 Edition Shape, Dimensions and Travel Angles of Drawbar Eyes for Full Trailers 全拖車用拖桿環首之形狀、尺度及活動範圍 |
|
|
|
CNS 7024
2020 Edition Cable Terminals for Automobiles (Type CA) 汽車用電線端子（塞型陽端子） |
|
|
|
CNS 11081
2020 Edition Method for Calculating Heat Balancing of Cement Rotary Kiln 水泥工業用窯爐之熱平衡計算方法 |
|
|
|
CNS 3745
2020 Edition Series 1 freight containers - Specification for corner fittings 第一類貨櫃－櫃角裝置規格 |
|
|
|
CNS 121
2020 Edition Collar (Using Heavy Duty Set Screws) 頸圈（用螺絲銷、重型） |
|
|
|
CNS 27
2020 Edition Transmission Equipment (Diameter of Transmission Shaft) 傳動設備（傳動軸之直徑） |
|
|
|
CNS 15227
2020 Edition Single-use medical examination gloves - Part 1: Specification for gloves made from rubber latex or rubber solution 單次使用之醫用檢驗手套－第１部：以乳膠或橡膠溶液製成之手套規格 |
|
|
|
CNS 13167
2020 Edition Safety Standards for Construction of Spindle Shapers 立軸機之構造安全基準 |
|
|
|
CNS 8930
2020 Edition Switchgears, Contact - Spring Washers 加強型彈簧墊圈（電器開關–接觸用） |
|
|
|
CNS 4238
2020 Edition Finishes and Tolerances of Bolts, Screws, Studs, and Nuts 螺栓、螺釘、螺樁、螺帽之加工精度及許可差 |
|
|
|
CNS 8408-2
2020 Edition Accelerated test methods for light fastness of coloured anodic oxide coatings on aluminium and aluminium alloys -Part 2:Test for light fastness to ultra-violet light 鋁及鋁合金之著色陽極氧化膜加速耐光性試驗法－第２部：紫外光堅牢度試驗法 |
|
|
|
CNS 4532
2020 Edition Terms Relating to the End (Point) of Fasteners 結件端部詞彙 |
|
|
|
CNS 13601
2020 Edition Method of test for flammability of children's sleepwear 兒童睡衣防焰性試驗法 |
|
|
|
CNS 8411-1
2020 Edition Test methods for abrasion resistance of anodic oxide coatings on aluminium and aluminium alloys - Part 1: Wheel wear test 鋁及鋁合金之陽極氧化膜耐磨耗性試驗法－ 第１部：磨輪磨耗試驗法 |
|
|
|
CNS 5561-3
2020 Edition Low Tension Cable Connections for Ignition Coils for Automobiles 汽車用點火線圈低壓接線端子 |
|
|
|
CNS 14104-4
2020 Edition Prosthetics and orthotics - Limb deficiencies - Part 3: Method of describing upper limb amputation stumps 義肢學與矯具學－肢體缺陷－第４部：導致截肢原因之描述 |
|
|
|
CNS 1864
2020 Edition Phosphorus Pentachloride 化學試藥（五氯化磷） |
|
|
|
CNS 1870
2020 Edition Picks, Two Taper Ends 化學試藥（苦味酸） |
|
|
|
CNS 15832-4-2
2020 Edition Method of test for paint components − Part 4-2: Analysis for components emitted from film − Volatile organic compounds 塗料成分試驗法－第4-2 部：塗膜釋出成分分析－揮發性有機化合物(VOC) |
|
|
|
CNS 7680
2020 Edition Shapes and Dimensions of Seats for Buses 大客車用座椅之形狀及尺度 |
|
|
|
CNS 16142
2020 Edition Balancing of rotating tools and tool systems 旋轉刀具及刀具系統之平衡調校 |
|
|
|
CNS 9746
2020 Edition Method of Test for Potential Expansion of Portland Cement Mortars Exposed to Sulfate 卜特蘭水泥墁料暴露於硫酸盬中之潛在膨脹檢驗法 |
|
|
|
CNS 80000-9
2020 Edition Quantities and units – Part 9: Physical chemistry and molecular physics 量及單位－第9部：物理化學與分子物理學 |
|
| Find out:15242Items | To Page of: First -Previous-Next -Last | [95] [96] [97] [98] [99] [100] [101] |
